Tandberg Data N3 5.3 Command

TANDBERG Gatekeeper User Manual

40

Configuration commands Description

xConfiguration Zones Zone [1..100]

Gatekeeper IP Port: <1..65534> Specifies the IP port of the neighbor gatekeeper

xConfiguration Zones Zone [1..100]

Gatekeeper HopCount: <1..255> Maximum hop count to use when issuing LRQs to Gatekeepers

in this zone.

The default is 15 hops.

xConfiguration Zones Zone [1..100]

Name: <zonename> Specifies the name of a zone in the zone list

xConfiguration Zones Zone [1..100]

Prefix Match: <prefix> Prefix to use for the indexed zone.

xConfiguration Zones Zone [1..100]

Prefix Mode: <Strip/Include> Whether or not to strip prefixes when forwarding an LRQ to the

indexed zone.

The default is Include.

5.3 Command

The command root command, xcommand, is used to execute commands on the Gatekeeper.

To list all xcommands type

xcommand ?

To get usage information for a specific command, type

xcommand <commandname> ?

Command Usage Description

AllowListAdd xCommand AllowListAdd

<allowed_alias> Adds an entry to the allow list, used by the registration

restriction policy.

AllowListDelete xCommand AllowListDelete

<index> Removes the pattern from the allow list at the specified

index.

Boot xCommand Boot Restarts (boots) the Gatekeeper.

This takes approximately 1 minute to complete.

CheckBandwidth xCommand CheckBandwidth

<node1> <node2> <bandwidth>

<calltype>

Diagnostic function for verifying bandwidth control. Node1,

Node2 are the case sensitive names of the nodes,

bandwidth the required bandwidth and calltype one of

Traversal or NonTraversal.

CredentialAdd xCommand CredentialAdd:

<username> <password> Adds the given username and password to the local

authentication database.

CredentialDelete xCommand CredentialDelete:

<index> Deletes the indexed credential.

DefaultLinksAdd xCommand DefaultLinksAdd Restores the factory default links for bandwidth control.

DefaultValuesSet xCommand DefaultValuesSet

Level: <level> Resets system parameters to default values.

Level 1 will reset most parameters, except networking

related ones. Level 2 and 3 reset progressively more

parameters.

Contents

Main Trademarks and copyright Environmental Issues TANDBERGs Environmental Policy Environmental Considerations Operator Safety Summary Table Of Contents Page 1 Introduction Page 2 Installation 2.1 Unpacking 2.2 Mounting 2.3 Connecting Cables 2.4 Switching on the System 2.5 Gatekeeper Initial Configuration Page 3 Using the Gatekeeper 3.1 System Administration 3.2 Registration 3.3 Neighbor Gatekeepers 3.4 Alternate Gatekeepers Page 3.5 Call Control Page Page 3.6 Bandwidth Control IP Page 3.6.1 Bandwidth Control and Firewall Traversal 3.6.2 Bandwidth Control Examples Enterprise Branch Office Home Office Home sub-zone Page 3.7 Registration Control 3.7.1 Registration Restriction Policy 3.7.2 Authentication 3.8 H.235 Authentication 3.8.1 Authentication using a local database 3.8.2 Authentication using an LDAP server Securing the LDAP connection with TLS 3.9 URI Dialing 3.9.1 URI Dialing and firewall traversal 3.9.2 Creating DNS SRV records 3.10 Firewall traversal 3.10.1 Calling unregistered endpoints 3.11 Call Policy 3.11.1 Making Decisions Based on Addresses address-switch address otherwise not-present 3.11.2 CPL Script Actions location proxy reject Selective Call Screening 3.11.3 Unsupported CPL Elements 3.11.4 CPL Examples Call screening Call Redirection 4 Software Upgrade 4.1 Upgrading Using HTTP(S) 4.2 Upgrading Using SCP Page 5 Configuring the Gatekeeper 5.1 Status xstatus ? xstatus TANDBERG Gatekeeper User Manual 5.2 Configuration xconfiguration ? xconfiguration xconfiguration <name> xconfiguration <name> ? xconfiguration <name> <param1>: value1 <param2>: value2 Page Page Page Page TANDBERG Gatekeeper User Manual 40 Configuration commands Description 5.3 Command xcommand ? To get usage information for a specific command, type xcommand <commandname> ? Command Usage Description Page 5.4 History xhistory ? xhistory xhistory <name> 5.5 Feedback 5.6 Other commands Page 6 Appendix: Configuring DNS Servers 6.1 Microsoft DNS Server 6.2 BIND 8 & 9 6.3 Verifying the SRV record 7 Appendix: Configuring LDAP Servers 7.1 Microsoft Active Directory 7.1.1 Prerequisites 7.1.2 Adding H.350 objects Create the organizational hierarchy Add the H.350 objects 7.2 OpenLDAP 7.2.1 Prerequisites 7.2.2 Installing the H.350 schemas 7.2.3 Adding H.350 objects Create the organizational hierarchy Add the H.350 objects 7.2.4 Securing with TLS 8 Approvals EMC Emission - Radiated Electromagnetic Interference EMC Immunity Electrical Safety 9 Technical Specifications 10 Index