Tandberg Data N3 - page 45

39

Configuration commands Description

xConfiguration SubZones

TraversalSubZone Bandwidth Total Mode:

<None/Limited/Unlimited>

Whether or not the traversal subzone is enforcing total

bandwidth restrictions. None corresponds to no bandwidth

available.

xConfiguration SubZones SubZone

[1..100] Bandwidth PerCall Limit:

<1..100000000>

Per-call bandwidth available on the indexed subzone.

xConfiguration SubZones SubZone

[1..100] Bandwidth PerCall Mode:

<None/Limited/Unlimited>

Whether or not the indexed subzone is enforcing per-call

bandwidth restrictions. None corresponds to no bandwidth

available.

xConfiguration SubZones SubZone

[1..100] Bandwidth Total Limit:

<1..100000000>

Total bandwidth available on the indexed subzone.

xConfiguration SubZones SubZone

[1..100] Bandwidth Total Mode:

<None/Limited/Unlimited>

Whether or not the indexed subzone is enforcing total

bandwidth restrictions. None corresponds to no bandwidth

available.

xConfiguration SubZones SubZone

[1..100] Name: <subzonename> Name of the indexed subzone.

xConfiguration SubZones SubZone

[1..100] Subnet IP Address: <IPAddr> IP to match an endpoint which belongs in this subzone.

xConfiguration SubZones SubZone

[1..100] Subnet IP Mask: <IPAddr> Subnet mask to match endpoints which belong in this subzone.

xConfiguration SystemUnit Name: <name> The name of the unit. Choose a name that uniquely identifies

the system.

xConfiguration SystemUnit Password:

<password> Specify the password of the unit. The password is used to login

with Telnet, HTTP(S), SSH, SCP, and on the serial port.

To set an empty password type

xConfiguration SystemUnit Password: ""

xConfiguration Telnet Mode: <On/Off> Enables/disables Telnet support.

You must restart the system for changes to take effect.

xConfiguration Traversal

AllowMediaDirect: <On/Off> Determines whether or not capable endpoints may send their

media directly to the Border Controller, bypassing the

Gatekeeper.

The defaults is Off.

xConfiguration Traversal Server

Address: <IPAddr> IP address of the Border Controller that this Gatekeeper should

connect to.

xConfiguration Traversal Registration

RetryInterval: <seconds> Frequency with which failed registrations with the Border

Controller should be repeated.

The default is 120 seconds.

xConfiguration Zones DefaultZone

Gatekeeper HopCount: <1..255> Maximum hop count to use when issuing LRQs to Gatekeepers

in this zone.

The default is 15 hops.

xConfiguration Zones TraversalZone

Gatekeeper HopCount: <1..255> Maximum hop count to use when issuing LRQs to Gatekeepers

in this zone.

The default is 15 hops.

xConfiguration Zones Zone [1..100]

Gatekeeper IP Address: <IPAddr> Specifes the IP address of neighbor gatekeeper.

Contents

Main Trademarks and copyright Environmental Issues TANDBERGs Environmental Policy Environmental Considerations Operator Safety Summary Table Of Contents Page 1 Introduction Page 2 Installation 2.1 Unpacking 2.2 Mounting 2.3 Connecting Cables 2.4 Switching on the System 2.5 Gatekeeper Initial Configuration Page 3 Using the Gatekeeper 3.1 System Administration 3.2 Registration 3.3 Neighbor Gatekeepers 3.4 Alternate Gatekeepers Page 3.5 Call Control Page Page 3.6 Bandwidth Control IP Page 3.6.1 Bandwidth Control and Firewall Traversal 3.6.2 Bandwidth Control Examples Enterprise Branch Office Home Office Home sub-zone Page 3.7 Registration Control 3.7.1 Registration Restriction Policy 3.7.2 Authentication 3.8 H.235 Authentication 3.8.1 Authentication using a local database 3.8.2 Authentication using an LDAP server Securing the LDAP connection with TLS 3.9 URI Dialing 3.9.1 URI Dialing and firewall traversal 3.9.2 Creating DNS SRV records 3.10 Firewall traversal 3.10.1 Calling unregistered endpoints 3.11 Call Policy 3.11.1 Making Decisions Based on Addresses address-switch address otherwise not-present 3.11.2 CPL Script Actions location proxy reject Selective Call Screening 3.11.3 Unsupported CPL Elements 3.11.4 CPL Examples Call screening Call Redirection 4 Software Upgrade 4.1 Upgrading Using HTTP(S) 4.2 Upgrading Using SCP Page 5 Configuring the Gatekeeper 5.1 Status xstatus ? xstatus TANDBERG Gatekeeper User Manual 5.2 Configuration xconfiguration ? xconfiguration xconfiguration <name> xconfiguration <name> ? xconfiguration <name> <param1>: value1 <param2>: value2 Page Page Page Page TANDBERG Gatekeeper User Manual 40 Configuration commands Description 5.3 Command xcommand ? To get usage information for a specific command, type xcommand <commandname> ? Command Usage Description Page 5.4 History xhistory ? xhistory xhistory <name> 5.5 Feedback 5.6 Other commands Page 6 Appendix: Configuring DNS Servers 6.1 Microsoft DNS Server 6.2 BIND 8 & 9 6.3 Verifying the SRV record 7 Appendix: Configuring LDAP Servers 7.1 Microsoft Active Directory 7.1.1 Prerequisites 7.1.2 Adding H.350 objects Create the organizational hierarchy Add the H.350 objects 7.2 OpenLDAP 7.2.1 Prerequisites 7.2.2 Installing the H.350 schemas 7.2.3 Adding H.350 objects Create the organizational hierarchy Add the H.350 objects 7.2.4 Securing with TLS 8 Approvals EMC Emission - Radiated Electromagnetic Interference EMC Immunity Electrical Safety 9 Technical Specifications 10 Index