Manuals / Tascam / Home Audio / Cassette Player

Tascam DA-45HR owner manual Block Diagram, Making control connections, Power connections

Models: DA-45HR

1 32

Page 8

1 - Introduction to the DA-45HR

the word clock master for a digital audio setup, any word clock slaves should receive the clock through the digital audio signal.

1.5.4 Making control connections

The optional RC-D45 remote control unit may be connected to the REMOTE IN jack, using the 5 m (approximately 16 ft) cable of the RC-D45.

WARNING

Do not attempt to use the tape deck with any remote control unit except one designed especially for use with this tape deck.

The CONTROL I/O connector is for use with suit- ably-equipped control units (see CONTROL I/O [36]).

1.5.5 Power connections

Make sure that your AC voltage supply matches the voltage requirements of the tape deck (as printed on the rear panel).

1.6 Block Diagram

8 TASCAM DA-45HR

Page 8

Image 8

Tascam owner manual Block Diagram, Making control connections, Power connections, Introduction to the DA-45HR

Contents

HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTUREDA-45HR Digital Audio Tape DeckImportant Safety Precautions IMPORTANT for U.K. CustomersGREEN-AND-YELLOW EARTH BLUE NEUTRAL BROWN LIVE 2 TASCAM DA-45HRIMPORTANT SAFETY INSTRUCTIONS Note to CATV system installerTASCAM DA-45HR …Read all of these InstructionsTable of Contents Table of Contents 1 - Introduction to the DA-45HR3 - Menu functions 4 - Advanced functionsTable of Contents 5 - RC-D45remote control unit option6 - Specifications 1.1 Features 1.3 Installation of the tape deck1 - Introduction to the DA-45HR 1.2 Unpacking and inspection1.5 Making connections 1.4.1 Head cleaning1.5.1 Making analog connections 1.5.2 Making digital audio connections1.6 Block Diagram 1.5.5 Power connections1.5.4 Making control connections 1 - Introduction to the DA-45HRTASCAM DA-45HR 2.1 Power and display 2.2Recording mode and source switches, etc1 POWER switch 4 CLOCK switch5 RECORD MODE switch 6Fs switch7 INPUT selector switch 8 DIGITAL INPUT selector switch9 ANALOG INPUT selector switch 2.3 Tape controls10 INPUT level controls 11 PHONES control and jack15 PLAY key 16 PAUSE key17 RECORD key 18 REC MUTE key2.4 Command keys 19 SHUTTLE wheel20 DATA dial 21 COUNTER MODE23 MARGIN RESET 22 CHAR24 DISPLAY 25 SKIP PLAY2.5 Rear panel 29 LOC30 LOC 31 SINGLE PLAY37 REMOTE IN 38 ~ IN39 BALANCED ANALOG inputs 40 UNBALANCED ANALOG inputs3 - Menu functions 3.1 Drum time head time3.2 Auto ID level 3.3 Auto ID time3.6 Digital output format 3.7 Digital out word length3.8 Dither 3.9 Copy prohibit3.14End tally signal 3.11HR time display3.12Repeat mode 3.13Pre-rolltime3.18Initializing settings 3.17Parameter save3 - Menu functions ENTER4 - Advanced functions 4.1 REPEAT4.2 CHECK 4.3 INS/+ and DEL4.4.1 Selecting an ID mode 4.4.2Manually writing a START or SKIP ID4.4.3 Writing a START or SKIP ID 4 - Advanced functions4.4.4 Writing an END ID 4.4.5 Erasing a START or SKIP ID4.4.6 Erasing an END ID 4.4.7 Erasing titles4.6.2 Setting location memories 4.5 The EDIT key4.6 Location memories 4.6.1 Locating to location memories4.7 Program mode 4.8 Character editing titling4.8.1 Entering and editing titles 4 - Advanced functions4.8.2 Writing the title to tape 4.8.3 Checking a title4.8.4 Deleting a title 4.8.5 Copying and pasting a title5 - RC-D45remote control unit option 5.1 Remote control transport keys56 MARGIN RESET 43 OPEN/CLOSE66 LOC 1 and LOC 2 keys 67 REC MUTE68 STOP 69 PLAY6 - Specifications 6.1 Audio speciﬁcations6.2I/O speciﬁcations 6.3 Physical speciﬁcations6.4 Dimensional drawing 6.5 Error messages6.5.2 Serious error messages 6.5.1 Warning messagesDA-45HR TEAC CORPORATION