Manuals / Taylor / Kitchen Appliance / Refrigerator

Taylor 430 TORQUE manual Step, Model 430 Torque, Operating Procedures

Models: 430 TORQUE

1 37

Download 37 pages 3.49 Kb

Page 17

Rotate the draw valve so the flats on the top of the draw valve are perpendicular to the door face.

Rotate the draw valve so the flats on the top of the draw valve are perpendicular to the door face.

Figure 12

Insert the ice buster through the door spout and into the slot located just above the lower o--ring.

Figure 13

With the ice buster in place, rotate the draw valve to allow installation of the draw handle. This will lock the ice buster in place. Install the draw handle pin, and close the draw valve by moving the handle to the left.

Place the large rubber gasket into the groove on the back side of the freezer door. Slide the white, plastic front bearing onto the bearing hub, making certain that the flanged end of the bearing is resting against the freezer door. DO NOT lubricate the door gasket or front bearing.

Figure 15

Step 6

Position the torque arm by inserting it through the slot in the torque switch arm and down into the hole in the torque rotor which protrudes from the door. Verify proper installation by moving the torque rotor back and forth to be sure it moves freely and easily.

Figure 16

Figure 14

Model 430 Torque

13

Operating Procedures

Image 17

Taylor 430 TORQUE Rotate the draw valve so the flats on the top of the draw valve are perpendicular to the door face, Step

Contents

Shake/Slush Freezer 3/97 Original Publication Updated 7/3/12Model 430 Torque Original Operating InstructionsInformation found on data plate Complete this page for quick reference when service is requiredE March, 1997 Taylor All rights reserved. 051430-M Taylor Company 750 N. Blackhawk Blvd Rockton, ILTable of Contents During Cleaning and Sanitizing Table of Contents - PageTroubleshooting Bacterial Count Regular Maintenance ChecksInstaller Safety To the InstallerSection Site PreparationElectrical Connections Air Cooled UnitsTo the Installer 101012Refrigerant Beater RotationTo the Installer 120709Section To the Operator061012 To the OperatorSafety SafetySection 110414Model 430 Torque Safety090114 Description Section 4 Operator Parts IdentificationPart Number DescriptionPart Number DescriptionDescription Part NumberPart Number DescriptionDescription Part NumberPower Switch Viscosity AdjustmentReset Button Indicator Light - “Mix Low”Assembly Operating ProceduresOperating Procedures SectionStep Operating ProceduresStep StepRotate the draw valve so the flats on the top of the draw valve are perpendicular to the door face Operating ProceduresStep Model 430 TorqueOperating Procedures SanitizingStep StepOperating Procedures PrimingStep StepDraining Product From The Freezing Cylinder Closing ProcedureRinsing Operating ProceduresDisassembly CleaningBrush Cleaning Operating ProceduresDuring Cleaning and Sanitizing Section 7 Important Operator ChecklistRegular Maintenance Checks Troubleshooting Bacterial CountModel 430 Torque Winter StorageImportant Operator Checklist Troubleshooting Guide Troubleshooting GuideSection PAGETroubleshooting Guide PROBLEMPROBABLE CAUSE REMEDYParts Replacement Schedule Section 9 Parts Replacement SchedulePART DESCRIPTION EVERYParts List Section Parts ListUPDATE Model 430 TorqueUPDATE Parts ListModel 430 Torque DESCRIPTIONUPDATE Parts ListModel 430 Torque DESCRIPTIONUPDATE Parts ListModel 430 Torque DESCRIPTIONUPDATE Parts ListModel 430 Torque DESCRIPTIONUPDATE Parts ListModel 430 Torque DESCRIPTIONUPDATE Parts ListModel 430 Torque DESCRIPTIONUPDATE Parts ListModel 430 Torque DESCRIPTIONUPDATE Parts ListModel 430 Torque DESCRIPTION7/3/12 Model 430 Torque7/3/12 Model 430 Torque