Air Cooled Units

DO NOT obstruct air intake and discharge openings: Air cooled units require a minimum of 3” (76.2 mm) of clearance around all sides of the freezer to allow for adequate air flow across condenser. Failure to allow adequate clearance can reduce the refrigeration capacity of the freezer and possibly cause permanent damage to the compressor.

Electrical Connections

This equipment is supplied with a 3--wire cord and grounding type plug, for connection to a single phase, 60 cycle, branch circuit supply. This unit must be plugged into a properly grounded receptacle. The cord and plug provided are 20A for 115/60/1 or 15A for 208--230/60/1; therefore, the wall outlet must also be 20A for 115/60/1 or 15A for 208--230/60/1. Check the data label, located on the side panel, for electrical specifications. Permanent wiring may be employed, if required by local codes. Instructions for conversion to permanent wiring are as follows:

1.Be sure the freezer is electrically disconnected.

2.Remove the appropriate panel and locate the small electrical box at the base of the freezer.

3.Remove the factory installed cord and strain relief bushing.

4.Route incoming permanent wiring through 7/8” (22 mm) hole in base pan.

5.Connect two power supply leads. Attach ground (earth) wire to the grounding lug inside the electrical box.

6.Be sure unit is properly grounded before applying power.

In the United States, this equipment is intended to be installed in accordance with the National Electrical Code (NEC), ANSI/NFPA 70-1987. The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising from the use of electricity. This code contains provisions considered necessary for safety. In all other areas of the world, equipment should be installed in accordance with the existing local codes. Please contact your local authorities.

FOLLOW YOUR LOCAL ELECTRICAL CODES!

101012

Each unit requires one power supply for each data label on the unit. Check the data label(s) on the freezer for branch circuit overcurrent protection or fuse, circuit ampacity, and other electrical specifications. Refer to the wiring diagram provided inside of the electrical box for proper power connections.

CAUTION: THIS EQUIPMENT MUST BE PROPERLY GROUNDED! FAILURE TO DO SO CAN RESULT IN SEVERE PERSONAL INJURY FROM ELECTRICAL SHOCK!

This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized installer. The installation location is marked by the equipotential bonding symbol (5021 of IEC 60417-1) on both the removable panel and the equipment’s frame.

SStationary appliances which are not equipped with a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation.

SAppliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 mA, particularly when disconnected, not used for long periods, or during initial installation, shall have protective devices such as a GFI to protect against the leakage of current, installed by authorized personnel to the local codes.

SSupply cords used with this unit shall be oil-resistant, sheathed flexible cable, not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion.

To the Installer

2

Model 430 Torque

Page 5 Page 7
Page 6
Image 6
Taylor 430 TORQUE manual Air Cooled Units, Electrical Connections
Page 5 Page 7

430 TORQUE specifications

The Taylor 430 TORQUE is a powerful and versatile machine designed for professional landscapers and agricultural operators looking to enhance their productivity and efficiency. Known for its robust construction and advanced technologies, the 430 TORQUE has made a name for itself in the industry, providing exceptional performance in various applications.

One of the standout features of the Taylor 430 TORQUE is its impressive engine capacity. Equipped with a high-performance engine, this machine delivers consistent torque and power, enabling operators to tackle even the toughest jobs with ease. The engine is designed for durability and longevity, ensuring that it can withstand the rigors of regular use in demanding environments.

In terms of design, the 430 TORQUE boasts a compact and lightweight profile, which increases its maneuverability. This makes it ideal for working in tight spaces and navigating around obstacles, allowing operators to achieve a greater level of precision in their work. The machine’s advanced hydraulic system provides smooth operation and responsive controls, further enhancing its performance and user experience.

One of the key technologies integrated into the Taylor 430 TORQUE is its intelligent control system. This system allows operators to monitor and adjust various parameters in real-time, optimizing performance according to specific job requirements. Features such as automatic speed adjustment and load sensing technology enable the machine to operate efficiently, reducing fuel consumption and minimizing wear and tear on the engine.

The 430 TORQUE is also equipped with a range of attachments, making it a versatile solution for different tasks. Whether it’s mowing, tilling, or excavating, operators can easily switch between attachments to suit their needs. This adaptability saves time and increases efficiency, making the machine a valuable asset for any landscaping or agricultural operation.

In terms of safety, the Taylor 430 TORQUE is designed with various protective features such as an ergonomic operator seat, safety guards, and emergency stop controls. These features ensure that operators can work with confidence and peace of mind, knowing that safety is a priority.

In summary, the Taylor 430 TORQUE stands out in the marketplace due to its exceptional power, advanced technologies, and versatile design. It is an invaluable tool for professionals in the landscaping and agricultural sectors, proving to be efficient, reliable, and user-friendly for a variety of tasks. With the Taylor 430 TORQUE, operators can expect to achieve excellent results while minimizing downtime and maximizing productivity.
Top Page Image Contents