CHAPTER 1 FPS1000 SERIES SPECIFICATIONS

 

FPS1000 SERIES SPECIFICATIONS

 

FPS1000-12

 

 

FPS1000-24

 

 

FPS1000-32

 

FPS1000-48

1

Rated output voltage

 

V

12

 

24

 

32

 

 

48

2

Output voltage set point

 

V

12+/-1%

 

24+/-1%

 

32+/-1%

 

 

48+/-1%

3

Output voltage range

 

V

10.5~13.2

 

21.5~29

 

28.8~38.4

 

 

43~58

4

Maximum Output Current (Refer to Fig.1)

 

A

72

 

40

 

31

 

 

21

5

Maximum output power

 

W

864

 

960

 

992

 

 

1008

6

Input voltage / frequency range

(*1)

---

 

 

 

85~265Vac continuous, 47~63Hz, Single phase

 

7

Maximum input current (at 100/200Vac)

 

A

 

 

 

 

12.0/6.0

 

 

 

8

Power Factor (Typ)

 

---

 

>0.98 at 115/230V and maximum output power

 

9

Efficiency (Typ)

(*2)

%

81/83%

 

 

84/86%

 

 

84/86%

 

 

85/88%

10

Inrush current

(*3)

A

 

 

 

Less than 40A

 

11

Hold-up time

 

mS

20mS typical at 100Vac input, rated output voltage and less than 80% of rated load.

12

Maximum line regulation

(*5)

---

 

 

 

 

0.40%

 

 

 

13

Max load regulation

(*6)

---

 

 

 

 

0.80%

 

 

 

14

Output Ripple and noise pk-pk

(*4)

mV

150

 

 

200

 

 

250

 

 

300

 

 

 

 

15

Temperature stability

 

---

0.05% of rated Vout for 8hrs after 30min warm-up. Constant line, load and temperature.

16

Temperature coefficient

 

PPM/°C

 

 

 

 

200

 

 

 

17

Remote sensing

(*7)

V

 

 

 

Possible. Refer to Instruction Manual.

 

18

Parallel operation

(*9)

---

 

 

 

Possible. Refer to Instruction Manual.

 

19

Series operation

 

---

 

 

 

Possible. Refer to Instruction Manual.

 

20

Over current protection

 

---

 

105~125% of maximum output current. Refer to Fig. 1

21

Over voltage protection

(*8)

V

14.3~15.7

31~34

 

 

41.5~45.5

 

 

62~66

22

Over temperature protection

 

---

 

 

 

Inverter shut down method, automatic reset.

 

23

Remote On/Off control

 

---

By electrical signal or dry contact. ON: 0~0.6V or short. OFF: 2~15V or open.

24

DC OK signal

 

---

Open collector signal. On when Vout>80+/-5% rated output. Max.sink current: 10mA

25

Over-Temp. warning

 

---

 

Open collector signal. Refer to Instruction Manual

 

26

AC fail signal

 

---

 

Open collector signal. Refer to Instruction Manual

 

27

Auxiliary power supply

 

---

 

 

 

11.2~12.5VDC. 0.25A Maximum output current.

 

28

Vout voltage trimming

 

---

Possible, via Vout Trim pin in the I/O connector. Refer to Instruction Manual.

29

Front panel indicators

 

---

 

 

 

AC OK, DC OK, DC FAIL

 

30

I2C Interface

 

---

 

 

 

Optional. Refer to Instruction Manual.

 

31

Operating temperature-models without IEC inlet

---

0~50°C: 100% load. Derate 2%/°C, 50°C to 60°C, Derate 2.5%/°C, 60°C to 70°C.

 

models with IEC inlet

---

 

0~50°C: 100% load. Derate 2%/°C, 50°C to 60°C.

 

32

Storage temperature

 

---

 

 

 

 

-30~85°C

 

33

Operating humidity

 

---

 

 

 

10~90% RH, no condensation.

 

34

Storage humidity

 

---

 

 

 

10~95% RH, no condensation.

 

35

Cooling

 

---

 

 

 

By internal Fans. Variable speed control.

 

36

Vibration

 

---

 

 

 

Built to meet ETS 300 019

 

37

Shock

 

---

 

 

 

Built to meet ETS 300 019

 

38

Conducted emission

(*10)

---

 

 

 

EN55022B, FCC part 15J-B, VCCI-B

 

39

Radiated emission

 

---

 

 

 

EN55022B, FCC part 15J-B, VCCI-B

 

40

Applicable safety standards

 

---

 

 

 

UL60950-1, EN60950-1

 

41

Withstand voltage

 

---

Input-Output: 3000Vrms, 1min. Input-Ground: 2000Vrms, 1min. Output-Ground: 500Vrms,1min.

42

Insulation resistance

 

---

More than 100Mohm at 25° C and 70% RH. Output-Ground: 500Vdc

43

Leakage current

 

mA

 

 

 

Less Than 1.1mA at 230Vac

 

44

Weight (Typ)

 

Kg

 

 

 

 

2.0

 

 

 

45

Size (W*H*D)

 

---

 

 

 

127x41x290mm. Refer to Outline Drawing.

 

Notes:

*1: For cases where conformance to various safety standards (UL, EN etc.) is required, to be described as 100-240Vac (50/60Hz).

*2: At 100/200Vac, rated load and 25˚C ambient temperature.

*3: Not applicable for the noise filter inrush current less than 0.2mS.

*4: Measured with JEITA RC-9131A 1:1 probe, 20MHz B.W.

*5: From 85~132Vac or 170~265Vac, constant load.

*6: From No-load to Rated load, constant input voltage. Measured at the sensing point in Remote sense.

*7: Remote sensing can compensate up to 1V drop on each load wire.

*8: Inverter shut down method. Reset by AC voltage recycle or by On/Off control.

*9: Derate Maximum output power by 10% for input voltage less than 100V RMS.

*10 For FPS 1000-12/P(S), when used not with FPS-S1U or FPS-T1U racks, an EMI suppressor clamp should be attached to the AC cable, as close as possible to the AC inlet, to meet class B.

Vout (V)

V2

Model

FPS1000

FPS1000

FPS1000

FPS1000

V/I

-12

-24

-32

-48

V1 (V)

12

24

32

48

V2 (V)

13.2

29

38.4

58

I1 (A)

66

33

26

17.25

I2 (A)

72

40

31

21

V1

I1

I2

Iout (A)

 

Fig. 1: Rated output current vs output voltage

4

Page 6 Page 8
Page 7
Image 7
TDK FPS1000-12, FPS-T1U, FPS-S1U, FPS1000-48, FPS1000-32, FPS1000-24 manual FPS1000 Series Specifications
Page 6 Page 8

FPS1000-32, FPS-S1U, FPS1000-48, FPS1000-12, FPS-T1U specifications

TDK has established itself as a leading innovator in power supply solutions with its range of FPS series products, specifically designed for various demanding applications. Among these, the FPS1000-24, FPS-T1U, FPS1000-12, FPS1000-48, and FPS-S1U models stand out due to their advanced features, robust technologies, and versatile characteristics.

The FPS1000-24, catering to a voltage output of 24V, is ideal for both industrial and commercial applications. It delivers a notable output power of 1000 watts while boasting high efficiency, making it a reliable option for systems that require consistent power with minimal energy loss. The model incorporates advanced protection features including over-voltage, over-current, and short-circuit protection, ensuring that connected devices are safeguarded against potential electrical faults.

Similarly, the FPS1000-12 offers a 12V output with equivalent power ratings, making it suitable for applications such as telecommunications and medical devices where stability and reliability are paramount. This model also emphasizes thermal management, utilizing integrated cooling technologies to maintain optimal performance even under demanding conditions.

The FPS1000-48 distinguishes itself with a 48V output, which is increasingly prevalent in high-density computing environments and server applications. With enhanced scalability, this model allows for multiple unit configurations to support higher load demands while maintaining exceptional efficiency levels.

In addition to the standard offerings, TDK’s FPS-T1U and FPS-S1U models provide intelligent power management solutions. The FPS-T1U, being a compact version, is tailored for space-constrained environments, ensuring high performance without compromising on size. It features built-in monitoring capabilities that allow users to track power usage and efficiency metrics in real-time.

The FPS-S1U is particularly notable for its modular design, enabling easy integration into various systems. This flexibility allows users to adapt the power supply to specific system requirements, enhancing functionality across diverse applications. Both models leverage cutting-edge technology to ensure low standby power consumption, reducing the overall energy footprint.

Overall, TDK’s FPS series exemplifies a commitment to quality, performance, and adaptability, making them ideal candidates for modern power supply needs across industries. With their comprehensive protection mechanisms, efficiency, and innovative designs, they stand as reliable choices for engineers and designers looking to optimize their systems.
Top Page Image Contents