TDK J Series JBW specifications JBW30W Type

(6/30)

JBW30W Type

SPECIFICATIONS AND STANDARDS

Part No.			JBW05-6R0	JBW12-2R5	JBW15-2R0	JAW24-1R3
Rated output voltage and current∗			5V • 6A	12V • 2.5A	15V • 2A	24V • 1.3A
Maximum output power		W	30	30	30	31.2
Input conditions
Input voltage Eac/Edc		V	85 to 265[Rating: 100 to 240]/110 to 370
Input frequency		Hz	47 to 440[Rating: 50 to 60](Single phase)
Input current		A	0.65typ./0.86max.[AC.100V]0.35typ./0.48max.[AC.240V]
Fuse rating		A	2[AC.250V, built-in]
Surge current		A	15typ./30max.[AC.100V]30typ./60max.[AC.240V] 1st surge current, cold start, reset after 1s minimum.
Leakage current		mA	0.35typ./0.75max.[AC.100V, 60Hz]0.5typ./0.75max.[AC.240V, 60Hz]
Power factor			0.6typ./0.45typ.[AC.100/240V]
Efficiency		%	75typ.[AC.100V]	78typ.[AC.100V]	79typ.[AC.100V]	80typ.[AC.100V]
		%	77typ.[AC.240V]	79typ.[AC.240V]	80typ.[AC.240V]	81typ.[AC.240V]
Output characteristics
Output voltage Edc		V	5	12	15	24
Voltage variable range Edc		V	Fixed	Fixed	Fixed	Fixed
Maximum output current		A	6	2.5	2	1.3
Minimum output current		A	0	0	0	0
Overvoltage threshold Edc		V	5.6min.	13.3min.	16.6min.	26.5min.
Overcurrent threshold		A	6.3min.	2.7min.	2.1min.	1.4min.
	Source effect	%	0.4max.[Within the input voltage range]
Voltage	Load effect	%	0.8max.[0 to 100% load]
	Temperature effect	%	2max.[Ambient temperature: –10 to +50°C]
stability
	Drift(Time effect)	%	0.4max.[25°C, input and output ratings, after input voltage ON for 30min to 8h]
	Recovery	%	±4max.[50 to 100% sudden load change]
Ripple Ep-p		mV	80max.	120max.	120max.	120max.
Ripple noise Ep-p		mV	120max.	150max.	150max.	150max.
Start up time		ms	650max.(350typ.)/320max.(130typ.)[AC.100/240V]
Hold up time		ms	20typ./160typ.[AC.100/240V]
Auxiliary functions
Indicator display			No
Overvoltage protection			Voltage shut-down type.
Overcurrent protection			Rectangular type(Winker operation), automatic recovery.
Remote ON-OFF			No
Remote sensing			No
Parallel operation			Impossible
Series operation			Impossible
Output voltage external variable function			No
Standards
Safety standards			UL60950-1, CSA C22.2 No.60950-1(C-UL), EN60950-1(TÜV) approved.
Noise terminal voltage			FCC-B, VCCI-B, EN55011-B, EN55022-B meet.
Input harmonics current requirement			No
Constructions
External dimensions		mm	26⋅ 55⋅ 122[H⋅ W⋅ L]
Weight		g	150max.
Mounting method			Can be attached to 1 side.
Case material			No(PWB Material: CEM3)

∗Current rating(maximum output current) is determined for –10 to +50°C. Derating is required when used outside this temperature range.

• Optional input, output cable kits are available at a separate price.

• All specifications are subject to change without notice.

004-02 / 20070523 / ea122_jbw