12V, 14.4V, 18V Cordless Drills

INSTRUCTIONS FOR USE: Charging The Battery

THE BATTERY(IES) MAY NOT BE FULLY CHARGED FROM THE FACTORY. READ ALL INSTRUCTIONS THOROUGHLY PRIOR TO FIRST USE.

The Drills covered by this manual use the same battery and battery charger.

Your Drill comes complete with a rechargeable battery which we recommend that you fully charge before the first use.

Drill must be charged for 8 hours prior to first use. After initial charge, allow approximately 3 to 8 hours to recharge your battery.

The battery should be recharged when the drill does not operate up to its normal performance level. Do not continue to operate the drill in this depleted capacity. Recharge the battery immediately.

To increase the life of your battery, do not leave the battery charging for more than 8 hours. While this is not a safety concern, overcharging may reduce the life of the battery.

Overtime, if drill is not used, the battery will lose capacity. For maximum performance, recharge the battery after prolonged storage or non-use periods.

NOTE: Before inserting or removing the battery from the charging base, always ensure that the base is not plugged into a 120V power source.

1.To begin charging, remove the battery pack from the tool by pressing on the battery release buttons on either side of the battery pack and pulling down.

2.Plug the battery pack into the battery charger making sure the positive (+) and negative (-) poles of the battery match the positive (+) and negative (-) poles of the battery charger.

NOTE: The battery will only fit into the battery charger and the tool one way.

3.Plug one end of the 120 Volt AC Adaptor into the battery charger and the other end into any standard 120 Volt wall outlet.The RED LED indicator on the battery charger will illuminate to indicate that the battery is charging.

4.Full charging will take between 3 to 8 hours.

5

Owner’s Manual

NOTE: While the battery is placed in the charger, the RED LED indicator light will remain on. If charging more than one battery, wait at least 15 minutes between each charge. Use only the battery charger that is supplied with this tool. Using another charger may cause damage to the battery.

WARNING: Never charge a battery pack again immediately after it has been fully charged.This can give rise to the battery pack being overcharged and a reduced battery life. DO NOT leave the battery pack in the charger for more than 8 hours.

Using The Drill

CAUTION: Always make sure that the tool is switched OFF and the battery pack is removed from the drill before changing any bits.

Loosen the keyless chuck by holding the ring and turning the sleeve counter clockwise. Select the drill bit or screwdriver you want to use and place it in the keyless chuck.Twist the sleeve of the keyless chuck clockwise to tighten it, making sure the drill bit remains in the center of the keyless chuck’s teeth.

Twist the 24 setting torque control ring to the desired setting. Lower settings are better for light work such as driving screws into soft materials. Higher settings are recommended for drilling into harder surfaces.

When properly adjusted, the clutch will slip at its present torque setting to prevent driving the screw too deep or to prevent damage to the tool.

To operate the drill in forward setting, simply keep the Forward/Lock/Reverse switch flat against the

side of the drill as shown.To change to reverse setting, move the Forward/Lock/Reverse switch until it is flat against the opposite side of the drill. Keeping the Forward/Lock/Reverse switch in the center position locks the drill and prevents unintentional use. It is recommended that the Drill is in the locked position when it is not in use or is being stored.

CAUTION: Always check the direction of the rotation before using the drill.

The speed of the drill is increased by the amount of pressure you place on the ON/OFF trigger switch.The less pressure you put on the trigger switch, the slower the drill will go.

6

Page 3 Page 5
Page 4
Image 4
Team Products PMD8127, PMD8131, PMD8129, PMD8133, PMD8128 Instructions for USE Charging The Battery, Using The Drill
Page 3 Page 5

PMD8127, PMD8129, PMD8133, PMD8128, PMD8131 specifications

The Team Products lineup, featuring models PMD8128, PMD8133, PMD8129, PMD8127, and PMD8131, offers a wide range of devices tailored for varied applications, each with unique features that cater to different user needs. These models are engineered using advanced technologies that ensure high performance and reliability.

The PMD8128 model is well-known for its robust design and versatility. It incorporates high-speed processing technology, enabling efficient handling of demanding tasks. It features a sleek interface that simplifies user interactions, making it suitable for both beginners and experienced users. With a durable build, this device can easily withstand tough environments without compromising on performance.

In contrast, the PMD8133 focuses on connectivity, offering multiple ports for seamless integration with other devices. Its advanced networking capabilities ensure that users can easily share data and resources across various platforms. The PMD8133 also boasts enhanced security features, providing peace of mind for users who prioritize data protection.

The PMD8129 stands out with its energy-efficient design, optimizing power consumption without sacrificing performance. This model is perfect for users looking to minimize their environmental footprint while still achieving optimal results. Additionally, its lightweight construction makes it highly portable, allowing users to carry it for on-the-go tasks.

For those seeking enhanced performance, the PMD8127 offers high processing power combined with a user-friendly interface. This model is designed for multitasking, allowing users to handle multiple applications seamlessly. With a premium display and superior sound quality, the PMD8127 is ideal for both work and entertainment.

Finally, the PMD8131 combines innovation and functionality, equipped with state-of-the-art technologies that enhance user experience. It features smart features like voice recognition and touch controls, making operations intuitive and engaging. The PMD8131 excels in both performance and aesthetics, making it a top choice for users who value style alongside functionality.

Together, these models from Team Products represent a blend of advanced technology, user-centric design, and reliable performance. Whether users require high processing speed, connectivity options, energy efficiency, multitasking capabilities, or innovative features, there is a model listed that meets their specific needs, ensuring satisfaction across diverse use cases.
Top Page Image Contents