Power Supply
|
|
|
|
|
|
|
| Eng | Front | Prod |
|
|
|
|
|
|
|
| Off |
| |
|
|
|
|
|
|
|
| Prod | Rear | Progr |
|
|
|
|
|
|
|
| Ext | Loc | |
|
|
| A | 1 | Clear |
| Mix |
|
| |
|
|
|
|
|
| Eng | ||||
Clear |
|
|
|
|
| |||||
|
|
|
|
|
| |||||
|
|
|
|
|
| Call | ||||
|
|
|
|
|
|
|
|
|
| |
|
| 4P | B | 2 | ND1/4 | CVBS (option) | 6 | |||
Star |
|
|
|
|
| |||||
|
|
|
|
|
| |||||
|
|
|
| 1/16 |
|
|
| |||
|
|
|
| 3 | ND |
|
|
| ||
|
|
| C |
|
|
|
| |||
|
| 6P |
|
|
|
|
| |||
Star |
|
|
|
|
|
| ||||
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| |||
|
|
|
| 1/64 |
|
|
|
| ||
|
|
| D | 4 | ND |
|
|
|
| |
|
|
|
|
|
|
|
| |||
| focus |
|
|
|
| Mic |
| |||
Soft |
|
|
|
|
|
| ||||
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| VF | Ext |
|
|
|
|
|
|
|
|
| Front Rear 48V |
|
| |
|
|
|
|
|
|
| Scrip |
|
|
|
|
|
|
|
|
|
| Light |
|
|
|
|
|
|
|
|
|
| Breaker |
| DC in | 5 |
|
|
|
|
|
|
| Power on |
|
| |
|
|
|
|
|
|
| TP |
| 48V On |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Ext 1 |
|
|
|
|
|
|
|
|
|
| Ext 2 |
|
|
|
|
|
|
|
|
|
| 12V 1,5A DC Out |
|
|
|
|
|
|
|
|
|
|
|
|
| Mic 2 |
|
|
|
|
|
|
| 2 |
|
| 4 |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| 3 |
|
| |
1 |
|
|
|
|
|
|
|
|
|
|
1 1 | Power switch | |
The power switch has two positions: | ||
On | : | Power to camera is switched on. |
Off | : | Power to camera is switched off. |
When you switch off the power, the access rights that were obtained by the use of the PIN code are disabled and the camera starts at the assigned user level when switched on again.
2 2 Power on indicator
The power on indicator lights when power is supplied to the camera and the camera power switch is on.
33 DC and Tally output socket
This socket supplies +12Vdc (±0.25V) when the camera is in the Triax mode (maximum current 1.5A). The socket also provides acces to an internal tally switch. When the camera is
4 4 Circuit breaker button (BREAKER)
If excessive current flows in the camera the circuit breaker trips and shuts off power to all the units. If this happens check the units for faults and if necessary take corrective action before pressing the circuit breaker button to reset the power.
5DC input socket
This socket accepts a DC supply voltage of 12V Nominal (11V to 17V) for powering the camera in
CAUTION
The input voltage must not exceed 17 Vdc.
6Triax cable socket
The power supply for the camera is normally supplied from the Base Station via the the triax cable. The triax cable is connected to this socket.
The triax cable also carries all the video, audio/ intercom and control signals between the camera and the Base Station.
Operator's Manual LDK 200 Triax | Location of Controls and Functions |
