1800123494 FV42XX-FV43XX FTD US_110x154 20/06/11 16:24 Page6

If there is a problem

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

Water drips from the

The chosen temperature is too low

Position the temperature control dial in the

holes of the soleplate.

and does not allow for the formation

steam range (from •• to MAX).

 

 

of steam.

 

 

 

 

You are using steam while the iron is

Wait until the temperature light goes out.

 

not hot enough.

 

 

 

You are using the Burst of Steam

Wait a few seconds before pressing the button

 

button too often.

again.

 

 

There is too much steam.

Move the steam control lever to a lower setting.

 

You have stored the iron horizontally,

See the section "Storing your iron".

 

 

without emptying it and without

 

 

 

setting it to

.

 

 

 

 

 

Brown streaks come

You are using chemical descaling

Do not add any descaling agents into the water

through the holes of the

agents.

 

tank.

 

soleplate and stain the

You are not using the right type of

Perform a self-cleaning operation and consult the

fabric.

water.

 

chapter "What type of water should be used?".

 

Fabric fibers have accumulated in

Perform the self-cleaning operation and clean

 

the holes of the soleplate and are

the soleplate with a damp sponge. Vacuum the

 

burning.

 

holes of the soleplate from time to time.

 

Your fabric has not been rinsed

Make sure that your fabric is rinsed sufficiently

 

sufficiently or you have ironed a new

so as to remove any deposits of soap or

 

garment before washing it.

chemical products on new clothes.

 

 

 

 

The soleplate is dirty or

The temperature is set too high.

Clean the soleplate with a damp sponge and

brown and is staining the

 

 

lower the temperature.

 

fabric.

 

 

You are using starch.

Clean the soleplate with a damp sponge.

 

 

 

Always spray starch onto the reverse side of the

 

 

 

fabric to be ironed.

 

 

 

 

 

There is little or no steam.

The water tank is empty.

Fill it.

 

 

The anti-scale valve is dirty.

Clean the anti-scale valve.

 

 

Your iron has a build-up of scale.

Clean the anti-scale valve and perform the self-

 

 

 

cleaning iron operation.

 

 

Your iron has been used dry for too

Perform the self-cleaning iron operation.

 

long.

 

 

 

The soleplate is

You have used your iron on an

The T-fal iron has a Lifetime warranty on the

scratched or damaged.

abrasive surface or it has been

soleplate (valid in USA and CANADA only) .

 

misused.

 

Please contact our consumer service depart-

 

 

 

ment at 1-800-395-8325.

 

Steam or water comes

The steam control lever is not set to

Set the steam control lever to

.

from the iron as you

the

position.

 

 

finish filling the tank.

The water tank is overfilled.

Never exceed the Max level .

 

 

 

 

 

The spray button does

The water tank is not filled enough.

Fill the water tank.

 

not spray water.

 

 

 

 

 

 

 

 

 

For all other problems or questions, please contact our Consumer Service Department at 1-800-395-8325 or visit us at www.t-falusa.com. Or in Canada at 1-800-418-3325 or visit our website at www.t-fal.ca. You may also contact an approved Service Center, please visit our website for their contact information.

6

Page 10 Page 12
Page 11
Image 11
Tefal FV4250C0, FV4250E0, FV4250E7, FV4250Y0, FV4250G0, FV4250M0 manual If there is a problem, Problem Possible Cause Solution
Page 10 Page 12

FV4250M1, FV4250Y0, FV4250K0, FV4250Z0, FV4250M0 specifications

The Tefal FV4250 series of steam irons, which includes models FV4250E7, FV4250C0, FV4250J0, FV4250G0, and FV4250E0, combines practicality with performance to meet modern ironing demands. These irons are designed for efficiency, ensuring users achieve flawless results on various fabric types.

One of the standout features of the Tefal FV4250 series is its powerful steam output. With up to 40 grams per minute of continuous steam delivery, these irons can easily tackle even the most stubborn creases. Additionally, the models boast a steam boost function that can reach up to 150 grams per minute, allowing for precise steam application on difficult areas or thicker fabrics like curtains and heavy linens.

The FV4250 models are equipped with an innovative Durilium soleplate technology. This unique soleplate design not only offers excellent steam distribution but also glides effortlessly over fabrics, reducing the effort required during ironing. The soleplate's non-stick surface makes it easy to clean, ensuring that you don’t have to deal with the residues from previous ironing tasks.

Moreover, the Tefal FV4250 series prioritizes user safety. They are designed with an auto shut-off feature that activates if the iron is left unattended for a certain period. This thoughtful safety mechanism provides peace of mind, especially for those who may juggle multiple household tasks while ironing.

In terms of convenience, the models in this series come with a large water tank, allowing for longer ironing sessions without the need for frequent refills. This is complemented by a built-in anti-calc system that reduces limescale build-up, ensuring the iron maintains its performance over time and extending the lifespan of the appliance.

Another notable characteristic of the Tefal FV4250 series is its ergonomic design. With a comfortable grip handle and a lightweight structure, these irons are designed to minimize fatigue during extended ironing sessions. The precision tip of the soleplate allows for easy navigation in hard-to-reach areas, such as around buttons and pleats.

Overall, the Tefal FV4250E7, FV4250C0, FV4250J0, FV4250G0, and FV4250E0 represent an excellent choice for anyone seeking a reliable, efficient, and stylish ironing solution, combining modern technology with user-friendly features to ensure an effortless and efficient ironing experience.
Top Page Image Contents