Manuals / Teledyne / Computer Equipment / Computer Monitor

Teledyne PEM 9002 manual Sound, Illum.off, Save, Continue, Start, Configuration Menu

Models: PEM 9002

1 49

Page 40

6.7 Configuration Menu
From the Program Start Menu:
Call up the Configuration Menu		S2
Changing the Configuration Data:
Sound	Switches the acoustic signal On / Off	S1
Illumination	Sets the time interval for the display back light	S2

Stores the configuration data		ENTER

Aborts the Configuration Menu		START
		STOP

Measure <START>

Memory <S1>

Config.<S2>

Batt:

S1	S2	S3

Sound	Yes
Illum.off	0
Save	< E >
Continue	<Start>

Auto-off Illumination Reset

Adjustable display illumination from 0 - 90 seconds

in increments of 5 seconds.

Page 40

Image 40

Teledyne PEM 9002 manual Sound, Illum.off, Save, Continue, Configuration Menu, From the Program Start Menu

Contents

Portable Emissions Monitor US - Version16830 Chestnut Street City of Industry, California 91748, USA TEL TOLL FREE FAXPage WARRANTY SUMMARY Page Table of Contents 1. Product Description b Measuring Procedure c Instrument Description 2. Physical Data + 32 F to + 1.850 F 0 C ... + 1.000 CCO2 = CO2max * 1 - ------- in % Volume 2.1 Calculation Formulae20.9 qA = T.Gas - T.Air * ---------- + B in %Combustion Air or Ambient Temperature Measurement Technical DataDraft or Pressure Measurement Oxygen O2 Measurement Carbon dioxide CO2 CalculationCarbon monoxide CO Measurement with H2 compensation ± 5 % of reading up to 4.000 ppmOptions Nitrogen monoxide NO MeasurementCO Measurement without H2 compensation Sulphur dioxide SO2 Measurement4 Front Panel Overview TELEDYNE5 Keypad Functions On / OffStart Measurements Fuel Selection Scroll Key6.1 Program Start Menu 6 User GuideSTART STOP S1 S2 6.2 Calibration Menu Batt6.3 Fuel Selection Natural Gas6.4 Additional Functions of the Measuring Program Gas Feed PumpSTART STOP6.5 Draft Measurement No pressure values Exceeding ± 60 inches of H2O ± 150 hPa mbar6.6 Menu Lines GraphicUnit Hold20.9 6.6.1 Menu LineZoom Info6.6.1.1 Menu Information Box If the failure or degrading keeps occuring and cannot be fixedplease contact the supplier Return6.6.1.2 Menu Time and Date InfoEdit.date Sensor6.6.2 Menu Line From the measuring program6.6.2.1 Menu Graphic Graphic6.6.2.3 Menu CO Purge System manual 6.6.2.2 Menu Core of waste gas flow Max. DraftCO-Protect 6.6.3 Menu Line 6.6.3.1 Menu Units6.6.3.2 Menu O2 - Reference Unit6.6.3.3 Menu Additional Data add. Data Advance to the next digit positionTerminate editing function Return6.6.4 Menu Line 6.6.4.1 Memory FunctionsMemory Calls up the memory program CaseCase 1 No memory blocks created Create new memory blockMemory Case 2 Memory blocks already existStores measured values in the selected block SaveOther Memory Functions Views selected memory blocksGraphics display of measured values Prints the stored measurement6.6.4.2 Menu Create Memory Blocks ABCabc Returns to the measuring menu Selects the next entry lineSelect 6.6.4.3 Menu Delete Memory Data ReturnReturn Delete allDelete all Clears all memories Deletes allAttention All memories inlcuding additional data will be deleted Deletes measurements onlyHold 6.6.4.4 Printing the Measured ValuesPrintout of current measuring values Intermediate storage of measured values6.7 Configuration Menu Call up the Configuration MenuChanging the Configuration Data Switches the acoustic signal On / OffReset Resets all instrument parametersConfirm Reset Auto-off Illumination Reset6.8 Entering the Company Address 7. System Maintenance See drawing on pageEmpty the condensate reservoir completely after each measuring pumps and sensors8. RS - 232 Interface 9. Battery / Line Voltage OperationStatus display of the Information on Charging the Battery Used or Dead Battery 2 x Screw M3x6 Printer Compartment Door Loading PaperPrinter Ribbon Paper 11. Waste Gas Cleaning System fine filterdry filtrate water trapCheck the microfilter for contaminations and change as necessary 11.1 PEM 9002 - Filters and other cleaner partsIf the pump capacity decreases, change the hydrophob filter

6.7 Configuration Menu

From the Program Start Menu:

Call up the Configuration Menu

Changing the Configuration Data:

Switches the acoustic signal On / Off

Stores the configuration data

Aborts the Configuration Menu

Sound

Illum.off

Save

Continue

<Start>