Manuals / Teledyne / Computer Equipment / Computer Monitor

Teledyne PEM 9002 Calculation Formulae, CO2 = CO2max * 1 - ------- in % Volume, 20.9 - O2

Models: PEM 9002

1 49

Page 11

2.1Calculation Formulae

		O2
Calculation of the CO2 value:		CO2 = CO2max * ( 1 - ------- ) in % Volume
		20.9
CO2max:	Max. CO2-value (fuel-specific) in % Volume.
O2:	Measured oxygen content in % Volume.
21:	Oxygen content of the air in % Volume.
		A2
Calculation of the waste gas loss:		qA = ( T.Gas - T.Air ) * (---------- + B) in %
		21 - O2
T.Gas:	Waste / flue gas temperature in °F or °C.
T.Room:	Combustion / ambient temperature in °F or °C.
A2, B:	Fuel-specific factors.

	CO2max	20.9
Calculation of the excess air value (Lambda):	Lambda = - ----------- =	------------
	CO2	20.9 - O2
Calculation of the combustion efficiency value (Eta):	Eta = 100 - qA in %
Calculation of CO 0% (undiluted):	CO0% = CO * Lambda	in ppm

Page 11

Image 11

Teledyne PEM 9002 Calculation Formulae, CO2 = CO2max * 1 - ------- in % Volume, Lambda = - ----------- =, 20.9 - O2

Contents

US - Version Portable Emissions MonitorTOLL FREE FAX 16830 Chestnut Street City of Industry, California 91748, USA TELPage WARRANTY SUMMARY Page Table of Contents 1. Product Description b Measuring Procedure c Instrument Description + 32 F to + 1.850 F 0 C ... + 1.000 C 2. Physical DataqA = T.Gas - T.Air * ---------- + B in % CO2 = CO2max * 1 - ------- in % Volume2.1 Calculation Formulae 20.9Draft or Pressure Measurement Technical DataCombustion Air or Ambient Temperature Measurement ± 5 % of reading up to 4.000 ppm Oxygen O2 MeasurementCarbon dioxide CO2 Calculation Carbon monoxide CO Measurement with H2 compensationSulphur dioxide SO2 Measurement OptionsNitrogen monoxide NO Measurement CO Measurement without H2 compensationTELEDYNE 4 Front Panel OverviewFuel Selection Scroll Key 5 Keypad FunctionsOn / Off Start MeasurementsSTART STOP S1 S2 6 User Guide6.1 Program Start Menu Batt 6.2 Calibration MenuNatural Gas 6.3 Fuel SelectionSTOP 6.4 Additional Functions of the Measuring ProgramGas Feed Pump STARTNo pressure values Exceeding ± 60 inches of H2O ± 150 hPa mbar 6.5 Draft MeasurementHold 6.6 Menu LinesGraphic UnitInfo 20.96.6.1 Menu Line ZoomReturn 6.6.1.1 Menu Information BoxIf the failure or degrading keeps occuring and cannot be fixed please contact the supplierSensor 6.6.1.2 Menu Time and DateInfo Edit.dateGraphic 6.6.2 Menu LineFrom the measuring program 6.6.2.1 Menu GraphicCO-Protect 6.6.2.2 Menu Core of waste gas flow Max. Draft6.6.2.3 Menu CO Purge System manual Unit 6.6.3 Menu Line6.6.3.1 Menu Units 6.6.3.2 Menu O2 - ReferenceReturn 6.6.3.3 Menu Additional Data add. DataAdvance to the next digit position Terminate editing functionCase 6.6.4 Menu Line6.6.4.1 Memory Functions Memory Calls up the memory programCreate new memory block Case 1 No memory blocks createdSave MemoryCase 2 Memory blocks already exist Stores measured values in the selected blockPrints the stored measurement Other Memory FunctionsViews selected memory blocks Graphics display of measured values6.6.4.2 Menu Create Memory Blocks ABCabc Select Selects the next entry lineReturns to the measuring menu Delete all 6.6.4.3 Menu Delete Memory DataReturn ReturnDeletes measurements only Delete all Clears all memoriesDeletes all Attention All memories inlcuding additional data will be deletedIntermediate storage of measured values Hold6.6.4.4 Printing the Measured Values Printout of current measuring valuesSwitches the acoustic signal On / Off 6.7 Configuration MenuCall up the Configuration Menu Changing the Configuration DataAuto-off Illumination Reset ResetResets all instrument parameters Confirm Reset6.8 Entering the Company Address pumps and sensors 7. System MaintenanceSee drawing on page Empty the condensate reservoir completely after each measuringStatus display of the 9. Battery / Line Voltage Operation8. RS - 232 Interface Information on Charging the Battery Used or Dead Battery Printer Ribbon Paper Loading Paper2 x Screw M3x6 Printer Compartment Door water trap 11. Waste Gas Cleaning Systemfine filter dry filtrateIf the pump capacity decreases, change the hydrophob filter 11.1 PEM 9002 - Filters and other cleaner partsCheck the microfilter for contaminations and change as necessary

2.1Calculation Formulae

CO2 = CO2max * ( 1 - ------- ) in % Volume

20.9

qA = ( T.Gas - T.Air ) * (---------- + B) in %

CO2max

Calculation of the excess air value (Lambda):

Lambda = - ----------- =

20.9 - O2

Calculation of the combustion efficiency value (Eta):

Eta = 100 - qA in %

Calculation of CO 0% (undiluted):

CO0% = CO * Lambda

in ppm