Manuals / Teledyne / Computer Equipment / Computer Monitor

Teledyne PEM 9002 manual Calibration Menu, Batt

Models: PEM 9002

1 49

Download 49 pages 50.86 Kb

Page 18

Image 18

6.2 Calibration Menu

Note: Do not place probe - Leave in ambient air until the unit is finished with the calibration phase.

Note: Any errors that occur during calibration are displayed on the information line.

Autozero

60 sec

DO NOT PLACE

PROBE

Batt:

Battery symbols:

empty full

Possible Error Messages:

Low Batt

Batt empty

T-Room Sensor ?

T-Gas Sensor ?

O2 Sensor defect

O2 Sens. Service

CO - Sensor ?

CO - Sensor defect

CO - val. overflow

NO - Sensor ?

NO - Sensor defect

NO - val. Overflow

Page 18

Image 18

Teledyne PEM 9002 manual Calibration Menu, Batt

Contents

Portable Emissions Monitor US - Version16830 Chestnut Street City of Industry, California 91748, USA TEL TOLL FREE FAXPage WARRANTY SUMMARY Page Table of Contents 1. Product Description b Measuring Procedure c Instrument Description 2. Physical Data + 32 F to + 1.850 F 0 C ... + 1.000 C20.9 CO2 = CO2max * 1 - ------- in % Volume2.1 Calculation Formulae qA = T.Gas - T.Air * ---------- + B in %Technical Data Combustion Air or Ambient Temperature MeasurementDraft or Pressure Measurement Carbon monoxide CO Measurement with H2 compensation Oxygen O2 MeasurementCarbon dioxide CO2 Calculation ± 5 % of reading up to 4.000 ppmCO Measurement without H2 compensation OptionsNitrogen monoxide NO Measurement Sulphur dioxide SO2 Measurement4 Front Panel Overview TELEDYNEStart Measurements 5 Keypad FunctionsOn / Off Fuel Selection Scroll Key6 User Guide 6.1 Program Start MenuSTART STOP S1 S2 6.2 Calibration Menu Batt6.3 Fuel Selection Natural GasSTART 6.4 Additional Functions of the Measuring ProgramGas Feed Pump STOP6.5 Draft Measurement No pressure values Exceeding ± 60 inches of H2O ± 150 hPa mbarUnit 6.6 Menu LinesGraphic HoldZoom 20.96.6.1 Menu Line Infoplease contact the supplier 6.6.1.1 Menu Information BoxIf the failure or degrading keeps occuring and cannot be fixed ReturnEdit.date 6.6.1.2 Menu Time and DateInfo Sensor6.6.2.1 Menu Graphic 6.6.2 Menu LineFrom the measuring program Graphic6.6.2.2 Menu Core of waste gas flow Max. Draft 6.6.2.3 Menu CO Purge System manualCO-Protect 6.6.3.2 Menu O2 - Reference 6.6.3 Menu Line6.6.3.1 Menu Units UnitTerminate editing function 6.6.3.3 Menu Additional Data add. DataAdvance to the next digit position ReturnMemory Calls up the memory program 6.6.4 Menu Line6.6.4.1 Memory Functions CaseCase 1 No memory blocks created Create new memory blockStores measured values in the selected block MemoryCase 2 Memory blocks already exist SaveGraphics display of measured values Other Memory FunctionsViews selected memory blocks Prints the stored measurement6.6.4.2 Menu Create Memory Blocks ABCabc Selects the next entry line Returns to the measuring menuSelect Return 6.6.4.3 Menu Delete Memory DataReturn Delete allAttention All memories inlcuding additional data will be deleted Delete all Clears all memoriesDeletes all Deletes measurements onlyPrintout of current measuring values Hold6.6.4.4 Printing the Measured Values Intermediate storage of measured valuesChanging the Configuration Data 6.7 Configuration MenuCall up the Configuration Menu Switches the acoustic signal On / OffConfirm Reset ResetResets all instrument parameters Auto-off Illumination Reset6.8 Entering the Company Address Empty the condensate reservoir completely after each measuring 7. System MaintenanceSee drawing on page pumps and sensors9. Battery / Line Voltage Operation 8. RS - 232 InterfaceStatus display of the Information on Charging the Battery Used or Dead Battery Loading Paper 2 x Screw M3x6 Printer Compartment DoorPrinter Ribbon Paper dry filtrate 11. Waste Gas Cleaning Systemfine filter water trap11.1 PEM 9002 - Filters and other cleaner parts Check the microfilter for contaminations and change as necessaryIf the pump capacity decreases, change the hydrophob filter