Texas Instruments 51X 6.5.3

6.5.3 Removing/Replacing the Heat Sink

To remove and replace the heat sink, perform the follow ing procedure:

1. Disconnect the AC adapter from the Notebook.

2. Remove the battery as described in Paragraph 6.5.1.

3. Loosen and tilt back the the keyboard assembly as described in

Paragraph 6.5.2.

4. Remove the four Phillips-head screws that secure the heat sink to the

main board.

5. Lift upward on the heat sink and remove it from the base.

6. Replacement is the reverse of Steps 1 through 5 above.

Slide Keyboard Release

Tabs toward front of

notebook.

Using a small

flat blade screwdriver,

gently pry keyboard up

along the front edge.

Remove ZIF

Cables from

Main Board

Figure 6-2 Removing/Replacing the Keyboard

Field Service 6-9

Contents

Main Page Contents Preface 1 General Description 2 Installation 3 Operating Instructions 4 Theory of Operation 5 Troubleshooting Procedures 6 Field Service ASelf Test Error Messages BPC-Doctor Diagnostics Preface Introduction Intended Audience Contents Other Manuals About the System Ordering Parts and Supplies 1 General Description 1.1 1.2 Model 510 Model 515 1.3 Configuration P/N Suffix Configuration P/N Suffix 1.4 Page Figure 1-2 Extensa 51x Series Features 1-4 General Description 1.4.1 1.4.2 1.4.3 n 1.4.3.1 Controls and Indicators ^ 1.4.4 1.4.5 Status LEDs 1.4.6 1.5 1.6 Subassemblies 1.6.1 1.6.2 1.7 Specifications Table 1-3 Extensa 51x Notebook Features Specifications Model 510 Model 515 General Description 1-13 * Weight specifications do not include AC Adapter 1.8 2 Installation 2.1 2.2 n 2.3 c n 2.3.1 Page 2.3.2 2.3.3 2.4 c 2.5 2.5.1 2.5.2 2.5.3 c 2.5.4 2.5.5 2.5.6 2.5.7 2.6 c 2.7 2.8 2.9 2.10 3 Operating Instructions n 3.1 3.2 3.2.1 3.2.2 Status LEDs 3.2.3 3.2.4 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 n 4 Theory of Operation 4.1 4.2 4.2.1 MAIN BOARD Figure 4-1 Notebook Functional Block Diagram 4-2 Theory of Operation 4.2.2 4.2.3 4.2.3.1 External VGA Drive Capability c 4.2.4 c 4.2.5 4.2.6 4.2.7 Page Table 4-4 Primary Battery Pack Specifications Function Specifications 4-8 Theory of Operation 5 Troubleshooting Procedures 5.1 5.2 SEE PARAGRAPH 5.3.3 Figure 5-1 Troubleshooting Flowchart 5-2 Troubleshooting 5.3 5.3.1 (EG. a lamp) to verify that voltage is present. If the voltage is OK, try replacing the AC Adapter 5-4 Troubleshooting MAIN BOARD n 5.3.3 5.3.4 5.3.5 5.3.5.1 Interactive Tests Page 5.3.5.3 Creating a Bootable Floppy Diskette n 5.3.5.4 Running PC-Doctor Page 6 Field Service c 6.1 6.2 6.2.1 c 6.2.2 6.2.3 6.2.4 6.3 c 6.4 and Assemblies 6.4.1 Page 6.4.2 Table 6-2 Base Assembly, Field-Replaceable Units (FRUs) FRU Description Page CRU Description c 6.5 c Replacement Procedures 6.5.1 Pack 6.5.2 n c 6.5.3 6.5.4 6.5.5 Assembly 6.5.6 Hard Drive Cover HDD Release Latches 6.5.7 6.5.8 6.5.9 or Contrast Board c 6.5.10 6.5.11 Control Board 6.5.12 Supply Board Assembly 6.5.13 6.5.14 Page A Self Test Error Messages A.1 Error Messages A-1 Error Message Corrective Action Table A-2 POST Checkpoint List A-2 Error Messages Error Messages A-3 A-4 Error Messages Page B PC-Doctor Diagnostics B.1 B.2 B.3 B.4 B.4.1 B.4.2 n B.4.3 B.4.4 B.4.5 B.5 B.6