Texas Instruments 51X 6.5.4

6.5.4 Opening/Replacing the Upper Case Assembly

To remove/replace the Top Case Assembly, perform the followi ng procedure:

1. Remove the AC Adapter, battery pack , any in stalled PCMCIA options,

the Keyboard Assembly and Heat Sink Assembly as described in

Paragraphs 6.5.1 through 6.5.3

2. Turn the notebook over and remove the six Phillips-head screws from

the bottom of the notebook. Then turn notebook rightsid e up.

3. Remove the four screws that secure the Top Case Assembly to the

base.

Remove set of

four screws

holding heat sink

Heat Sink

Assembly

Release keyboard

assembly and

tilt up against

Display.

Figure 6-3 Removing/Replacing the Heat Sink Assembly

6-10 Field Service

Contents

Main Page Contents Preface 1 General Description 2 Installation 3 Operating Instructions 4 Theory of Operation 5 Troubleshooting Procedures 6 Field Service ASelf Test Error Messages BPC-Doctor Diagnostics Preface Introduction Intended Audience Contents Other Manuals About the System Ordering Parts and Supplies 1 General Description 1.1 1.2 Model 510 Model 515 1.3 Configuration P/N Suffix Configuration P/N Suffix 1.4 Page Figure 1-2 Extensa 51x Series Features 1-4 General Description 1.4.1 1.4.2 1.4.3 n 1.4.3.1 Controls and Indicators ^ 1.4.4 1.4.5 Status LEDs 1.4.6 1.5 1.6 Subassemblies 1.6.1 1.6.2 1.7 Specifications Table 1-3 Extensa 51x Notebook Features Specifications Model 510 Model 515 General Description 1-13 * Weight specifications do not include AC Adapter 1.8 2 Installation 2.1 2.2 n 2.3 c n 2.3.1 Page 2.3.2 2.3.3 2.4 c 2.5 2.5.1 2.5.2 2.5.3 c 2.5.4 2.5.5 2.5.6 2.5.7 2.6 c 2.7 2.8 2.9 2.10 3 Operating Instructions n 3.1 3.2 3.2.1 3.2.2 Status LEDs 3.2.3 3.2.4 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 n 4 Theory of Operation 4.1 4.2 4.2.1 MAIN BOARD Figure 4-1 Notebook Functional Block Diagram 4-2 Theory of Operation 4.2.2 4.2.3 4.2.3.1 External VGA Drive Capability c 4.2.4 c 4.2.5 4.2.6 4.2.7 Page Table 4-4 Primary Battery Pack Specifications Function Specifications 4-8 Theory of Operation 5 Troubleshooting Procedures 5.1 5.2 SEE PARAGRAPH 5.3.3 Figure 5-1 Troubleshooting Flowchart 5-2 Troubleshooting 5.3 5.3.1 (EG. a lamp) to verify that voltage is present. If the voltage is OK, try replacing the AC Adapter 5-4 Troubleshooting MAIN BOARD n 5.3.3 5.3.4 5.3.5 5.3.5.1 Interactive Tests Page 5.3.5.3 Creating a Bootable Floppy Diskette n 5.3.5.4 Running PC-Doctor Page 6 Field Service c 6.1 6.2 6.2.1 c 6.2.2 6.2.3 6.2.4 6.3 c 6.4 and Assemblies 6.4.1 Page 6.4.2 Table 6-2 Base Assembly, Field-Replaceable Units (FRUs) FRU Description Page CRU Description c 6.5 c Replacement Procedures 6.5.1 Pack 6.5.2 n c 6.5.3 6.5.4 6.5.5 Assembly 6.5.6 Hard Drive Cover HDD Release Latches 6.5.7 6.5.8 6.5.9 or Contrast Board c 6.5.10 6.5.11 Control Board 6.5.12 Supply Board Assembly 6.5.13 6.5.14 Page A Self Test Error Messages A.1 Error Messages A-1 Error Message Corrective Action Table A-2 POST Checkpoint List A-2 Error Messages Error Messages A-3 A-4 Error Messages Page B PC-Doctor Diagnostics B.1 B.2 B.3 B.4 B.4.1 B.4.2 n B.4.3 B.4.4 B.4.5 B.5 B.6