Texas Instruments 51X 6.5.14

6. Using a small flat blade screwdriver and apply light pressure in a

rocking motion to remove the hard drive cable connector.

7. Remove four Phillips-head screws (one on each of the four sides of the

heat sink opening) securing the board to the base assembly. Do not

remove the smaller screws which are part of the PCMCIA connector

hardware.

8. Remove the Phillips head screw at the left rear of the Main Board.

9. Lift up along the front edge of the Main Board Assembly until it clears

the hard drive cavity; then pull the board forward and out of the

plastics.

10. Refer to Paragraph 6.5.14 and transfer the CPU to the replacement

Main Board.

11. Inspect the two configuration DIP sw itches on the replacement board;

ensure that the settings are as described in Figure 6-5.

12. Reassembly is essentially the reverse of Steps 1 through 9 above.

6.5.14 Removing/Replacing the Pentium Chip

The illustration in Figure 6-6 shows the procedure for removing/replacing

the processor from/to the processor socket on the Main Board.

1. Remove the Main Board assembly as described in Paragraph 6.5.13.

2. Insert a small flat-blade screwdriver into the rightmost opening as

shown in Figure 6-6.

ON

1

2

3

4SW1

All

OFF

SW2

Switch 4

ON, all

others OFF ON

1

2

3

4

Figure 6-5 Switch Settings for Main Board

6-16 Field Service

Contents

Main Page Contents Preface 1 General Description 2 Installation 3 Operating Instructions 4 Theory of Operation 5 Troubleshooting Procedures 6 Field Service ASelf Test Error Messages BPC-Doctor Diagnostics Preface Introduction Intended Audience Contents Other Manuals About the System Ordering Parts and Supplies 1 General Description 1.1 1.2 Model 510 Model 515 1.3 Configuration P/N Suffix Configuration P/N Suffix 1.4 Page Figure 1-2 Extensa 51x Series Features 1-4 General Description 1.4.1 1.4.2 1.4.3 n 1.4.3.1 Controls and Indicators ^ 1.4.4 1.4.5 Status LEDs 1.4.6 1.5 1.6 Subassemblies 1.6.1 1.6.2 1.7 Specifications Table 1-3 Extensa 51x Notebook Features Specifications Model 510 Model 515 General Description 1-13 * Weight specifications do not include AC Adapter 1.8 2 Installation 2.1 2.2 n 2.3 c n 2.3.1 Page 2.3.2 2.3.3 2.4 c 2.5 2.5.1 2.5.2 2.5.3 c 2.5.4 2.5.5 2.5.6 2.5.7 2.6 c 2.7 2.8 2.9 2.10 3 Operating Instructions n 3.1 3.2 3.2.1 3.2.2 Status LEDs 3.2.3 3.2.4 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 n 4 Theory of Operation 4.1 4.2 4.2.1 MAIN BOARD Figure 4-1 Notebook Functional Block Diagram 4-2 Theory of Operation 4.2.2 4.2.3 4.2.3.1 External VGA Drive Capability c 4.2.4 c 4.2.5 4.2.6 4.2.7 Page Table 4-4 Primary Battery Pack Specifications Function Specifications 4-8 Theory of Operation 5 Troubleshooting Procedures 5.1 5.2 SEE PARAGRAPH 5.3.3 Figure 5-1 Troubleshooting Flowchart 5-2 Troubleshooting 5.3 5.3.1 (EG. a lamp) to verify that voltage is present. If the voltage is OK, try replacing the AC Adapter 5-4 Troubleshooting MAIN BOARD n 5.3.3 5.3.4 5.3.5 5.3.5.1 Interactive Tests Page 5.3.5.3 Creating a Bootable Floppy Diskette n 5.3.5.4 Running PC-Doctor Page 6 Field Service c 6.1 6.2 6.2.1 c 6.2.2 6.2.3 6.2.4 6.3 c 6.4 and Assemblies 6.4.1 Page 6.4.2 Table 6-2 Base Assembly, Field-Replaceable Units (FRUs) FRU Description Page CRU Description c 6.5 c Replacement Procedures 6.5.1 Pack 6.5.2 n c 6.5.3 6.5.4 6.5.5 Assembly 6.5.6 Hard Drive Cover HDD Release Latches 6.5.7 6.5.8 6.5.9 or Contrast Board c 6.5.10 6.5.11 Control Board 6.5.12 Supply Board Assembly 6.5.13 6.5.14 Page A Self Test Error Messages A.1 Error Messages A-1 Error Message Corrective Action Table A-2 POST Checkpoint List A-2 Error Messages Error Messages A-3 A-4 Error Messages Page B PC-Doctor Diagnostics B.1 B.2 B.3 B.4 B.4.1 B.4.2 n B.4.3 B.4.4 B.4.5 B.5 B.6