Texas Instruments 51X 2.5.4

2.5.4 Installing External VGA Monitor

The notebook is capable of driving both its internal LCD di splay and an

external VGA monitor (LCD only, simultaneous, or VGA only). The external

monitor connector pinouts and connector locations are shown in Fig ure 2-8.

To install an external monitor with the notebook, use the fol lowing steps:

1. Ensure that both the notebook and the exte rnal monitor are turned

off.

2. Locate the 15-pin female VGA port on the rear of the notebook.

3. Attach the appropriate end of the monitor cable to the VGA port on

your notebook. If the monitor cable connectors have retaining screws,

tighten them down.

4. If necessary, connect the monitor power cable to the monitor, and

plug the monitor power cable into an electrical outlet.

5. Power on the monitor, as well as any other peripheral devices

connected to the notebook; then power up the notebook.

1

2

3

4

5

6

7

8

9

10

11, 12

13

14

15

RED VIDEO

GREEN VIDEO

BLUE VIDEO

NOT USED

GROUND

RED RETURN

GREEN RETURN

BLUE RETURN

NOT USED

GROUND

NOT USED

HORIZONTAL SYNC

VERTICAL SYNC

NOT USED

OUTPUT

OUTPUT

OUTPUT

INPUT

INPUT

INPUT

OUTPUT

OUTPUT

PIN

SIGNAL NAME

DIRECTION

EXTERNAL VGA CONNECTOR PINOUTS

1

2

3

4

5

7

8

9

10

6

1112131415

Figure 2-8 External Monitor Port Pinouts

Installation 2-9

Contents

Main Page Contents Preface 1 General Description 2 Installation 3 Operating Instructions 4 Theory of Operation 5 Troubleshooting Procedures 6 Field Service ASelf Test Error Messages BPC-Doctor Diagnostics Preface Introduction Intended Audience Contents Other Manuals About the System Ordering Parts and Supplies 1 General Description 1.1 1.2 Model 510 Model 515 1.3 Configuration P/N Suffix Configuration P/N Suffix 1.4 Page Figure 1-2 Extensa 51x Series Features 1-4 General Description 1.4.1 1.4.2 1.4.3 n 1.4.3.1 Controls and Indicators ^ 1.4.4 1.4.5 Status LEDs 1.4.6 1.5 1.6 Subassemblies 1.6.1 1.6.2 1.7 Specifications Table 1-3 Extensa 51x Notebook Features Specifications Model 510 Model 515 General Description 1-13 * Weight specifications do not include AC Adapter 1.8 2 Installation 2.1 2.2 n 2.3 c n 2.3.1 Page 2.3.2 2.3.3 2.4 c 2.5 2.5.1 2.5.2 2.5.3 c 2.5.4 2.5.5 2.5.6 2.5.7 2.6 c 2.7 2.8 2.9 2.10 3 Operating Instructions n 3.1 3.2 3.2.1 3.2.2 Status LEDs 3.2.3 3.2.4 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 n 4 Theory of Operation 4.1 4.2 4.2.1 MAIN BOARD Figure 4-1 Notebook Functional Block Diagram 4-2 Theory of Operation 4.2.2 4.2.3 4.2.3.1 External VGA Drive Capability c 4.2.4 c 4.2.5 4.2.6 4.2.7 Page Table 4-4 Primary Battery Pack Specifications Function Specifications 4-8 Theory of Operation 5 Troubleshooting Procedures 5.1 5.2 SEE PARAGRAPH 5.3.3 Figure 5-1 Troubleshooting Flowchart 5-2 Troubleshooting 5.3 5.3.1 (EG. a lamp) to verify that voltage is present. If the voltage is OK, try replacing the AC Adapter 5-4 Troubleshooting MAIN BOARD n 5.3.3 5.3.4 5.3.5 5.3.5.1 Interactive Tests Page 5.3.5.3 Creating a Bootable Floppy Diskette n 5.3.5.4 Running PC-Doctor Page 6 Field Service c 6.1 6.2 6.2.1 c 6.2.2 6.2.3 6.2.4 6.3 c 6.4 and Assemblies 6.4.1 Page 6.4.2 Table 6-2 Base Assembly, Field-Replaceable Units (FRUs) FRU Description Page CRU Description c 6.5 c Replacement Procedures 6.5.1 Pack 6.5.2 n c 6.5.3 6.5.4 6.5.5 Assembly 6.5.6 Hard Drive Cover HDD Release Latches 6.5.7 6.5.8 6.5.9 or Contrast Board c 6.5.10 6.5.11 Control Board 6.5.12 Supply Board Assembly 6.5.13 6.5.14 Page A Self Test Error Messages A.1 Error Messages A-1 Error Message Corrective Action Table A-2 POST Checkpoint List A-2 Error Messages Error Messages A-3 A-4 Error Messages Page B PC-Doctor Diagnostics B.1 B.2 B.3 B.4 B.4.1 B.4.2 n B.4.3 B.4.4 B.4.5 B.5 B.6