| * Label size is not specified | * Check if label size is setup correctly. |
|
| |||||
| properly. |
|
| ||||||
| * Calibrate the sensor by Auto Gap or |
|
| ||||||
| * Sensor sensitivity is not set |
|
| ||||||
Skip labels when printing | Manual Gap options. |
|
|
| |||||
properly. |
|
|
| ||||||
| * Clear the |
| |||||||
| * The media sensor is covered with |
| |||||||
| dust. | blower. |
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
| * Calibrate the sensor sensitivity again. |
| ||||||
|
| * Set the correct label size and gap size. |
| ||||||
|
| * Press [MENU] [SELECT] |
|
| |||||
|
| x3[DOWN]x6 [SELECT] to fine tune | |||||||
|
| the parameter of Shift Y. |
|
| |||||
|
| * If using the software BarTender, please |
| ||||||
|
| set the vertical offset in the driver. |
|
| |||||
| * Media sensor sensitivity is not set |
|
|
|
|
|
|
| |
| properly. |
|
|
|
|
|
|
| |
The printing position of small | * Label size is incorrect. |
|
|
|
|
|
|
| |
label is incorrect | * The parameter Shift Y in the LCD |
|
|
|
|
|
|
| |
menu is incorrect. |
|
|
|
|
|
|
| ||
| * The vertical offset setting in the |
|
|
|
|
|
|
| |
| driver is incorrect. |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
The left side printout position is | * Wrong label size setup. | * Set the correct label size. |
|
| |||||
* Press [MENU] | | [SELECT] x | 3 | | |||||
| * The parameter Shift X in LCD |
|
|
| |||||
incorrect | menu is incorrect. | [DOWN] x 5 [SELECT] to fine tune the | |||||||
parameter of Shift X. |
|
|
| ||||||
|
|
|
|
| |||||
Missing printing on the left or | * Wrong label size setup. | * Set the correct label size. |
|
| |||||
right side of label |
|
| |||||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
RTC time is incorrect when | * The battery has run down. | * Check if there is a battery on the main | |||||||
| |||||||||
reboot the printer | board. |
|
|
|
|
| |||
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
Power and Error LEDs are | * Power switch OFF and ON too | * Turn off the printer and wait all LEDs are | |||||||
| |||||||||
blinking fast | fast. | dark, and turn on the printer again. |
|
| |||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
| * Print head pressure is incorrect. | * Make sure the label guide touch the edge | |||||||
| * Ribbon installation is incorrect. | ||||||||
| of the media guide. |
|
|
| |||||
Wrinkle Problem | * Media installation is incorrect. |
|
|
| |||||
* Make sure label, paper core and ribbon | |||||||||
| * Print density is incorrect. | ||||||||
| are set at the center of the spindle. |
|
| ||||||
| * Media feeding is incorrect. |
|
| ||||||
|
|
|
|
|
|
|
| ||
Gray line on the blank label | * The print head is dirty. | * Clean the print head. |
|
|
| ||||
* The platen roller is dirty. | * Clean the platen roller. |
|
| ||||||
|
|
| |||||||
Irregular printing | * The printer is in Hex Dump mode. | * Turn off and on the printer to skip the |
|
| |||||
* The | dump mode. |
|
|
|
|
| |||
| * |
|
| ||||||
|
|
|
|
37