(SRM-4)

OPERATION

IMPORTANT: DO NOT use a non-CV tractor shaft. Driveline damage will occur when turning the implement.

IMPORTANT: Do not operate the PTO with the flex arm in the transport position for extended periods of time. This may cause driveline vibration and will accelerate universal joint wear.

WARNING!

When attaching the PTO yoke to the Tractor PTO shaft, it is important that the spring activated locking collar slides freely and the locking balls are seated securely in the groove of the PTO shaft. A driveline not attached correctly to the Tractor PTO shaft could slip off and result in personal injury and damage to the cutter.

7.1 Constant Velocity (CV) Driveline

For mowers equipped with a Constant Velocity (CV) driveline, the maximum turning angle between the tractor and mower must be determined to ensure the joint angle does not over-extend which can cause CV joint damage. Constant Velocity joints enable the driveline to operate smoothly with no vibrations and clattering at angles up to 70°. Angles greater than 80° can result in mechanical damage to the CV joint and mower driveline.

The Constant Velocity joint must be lubricated every 8 hours of operation as specified in the Maintenance Section. Failure to properly lubricate the joint will result in accelerated wear and joint component failure.

CV Driveline Maximum Angle Check Procedure

1.With the mower attached to the tractor and the driveline disconnected from the tractor PTO stub make a hard left turn until there is approximately a 1" clearance between the left rear tractor tire and mower frame or tongue.

2.Stop and completely shut down the tractor. Place the tractor in Park and apply the Parking Brake before dismounting.

3.Check the CV joint at this maximum turning radius by holding the driveline yoke above the PTO shaft and then angle the CV joint to its maximum angle. A minimum difference of 10 degrees between the center line of the yoke and the PTO shaft must be maintained to ensure the joint will not be over angled. If the joint cannot be angled at least 10°, there is a potential problem of over-angling the joint while making sharp turns.

4.Solutions: To ensure the joint is not damaged, check the following:

-Check the drawbar length to ensure that it is at the proper length for the RPM speed of the mower. -Move the tractor rear tires wider apart to limit the tractor turning radius.

-Position the mower at multiple angles and perform the above procedure. Determine the sharpest turning radius that maintains a safe operating angle and note this position to the operator.

OPERATION

DANGER!

10 DEG.

80 DEG.

80 DEG.

CONSTANT VELOCITY JOINT-MAXIMUM ANGLE CHECK

Do not turn so sharp or lift mower so high to produce a severe "knocking" of the Driveline which will cause accelerated wear and breakage of drive train components and could result in possible injury from the separated Driveline sections.

FLX15/10 04/06

Operation Section 4-17

© 2006 Alamo Group Inc.

Page 60 Page 62
Page 61
Image 61
Tiger FLX15, FLX10 manual Constant Velocity CV Driveline, CV Driveline Maximum Angle Check Procedure
Page 60 Page 62

FLX15, FLX10 specifications

Tiger FLX10 and FLX15 are advanced multi-functional devices that have been designed to cater to diverse industrial and commercial needs. These machines stand out in their respective sectors due to their superior features, cutting-edge technologies, and robust characteristics, making them suitable for various applications.

The Tiger FLX10 brings a host of features that enhance productivity and efficiency. At its core, it integrates a powerful multi-core processor that ensures high-speed performance, allowing users to handle complex tasks with ease. The device is equipped with an intuitive user interface, which simplifies navigation and allows for seamless operation. The FLX10 also boasts impressive multitasking capabilities, enabling users to run multiple applications simultaneously without any lag, thus streamlining workflows.

On the other hand, the FLX15 takes performance a notch higher with its enhanced processing power and memory capacity. It is tailored for more demanding applications, making it ideal for industries requiring high-level data processing and analytics. This model features advanced connectivity options, including Wi-Fi, Bluetooth, and USB ports, facilitating easy integration with other devices and systems. Additionally, the FLX15 supports robust security features, safeguarding sensitive data and ensuring compliance with industry standards.

Both models incorporate advanced technologies that improve functionality. For instance, they utilize state-of-the-art thermal management systems, ensuring optimal performance even in high-temperature environments. The machines are designed with energy efficiency in mind, reducing power consumption while maintaining high output levels, which is a significant consideration for environmentally conscious users.

In terms of durability, both the Tiger FLX10 and FLX15 are constructed using high-quality materials, making them resistant to wear and tear. Their rugged design ensures longevity, minimizing downtime and maintenance costs. Furthermore, these devices come equipped with comprehensive support and warranty options, providing users with peace of mind regarding their investment.

In summary, the Tiger FLX10 and FLX15 are exemplary devices that embody modern technological advancements in industrial applications. With their powerful performance, user-friendly interfaces, advanced connectivity, and robust durability, they stand out as reliable solutions in today’s fast-paced business environment. Both models are well-positioned to meet the evolving demands of various sectors, making them valuable assets for companies looking to enhance their operational efficiency.
Top Page Image Contents