ASSEMBLY

BOOM MOUNTING BRACKET

Using a floor jack and / or a hoist, raise the boom mounting bracket up to level and slide the bracket into position onto main frame as shown in parts section.

Install pin through main frame and bracket. Secure with cap-screw, lock-washer and hex nut through boss on main frame as shown.

Secure mounting bracket to main frame with the cap-screws, lock-washers, flat- washers, cut flat-washers and hex nuts provided. Secure using the two slotted holes on the bracket and main frame.

SWIVEL BRACKET MOUNTING

Install the boom swivel bracket onto the boom mounting bracket with the swivel pin. Secure the pin in place using the capscrews, etc. through the hole in the boss and pin. NOTE: The head of the capscrew must be toward the front of the tractor.

Install all new swivels and fittings on the swing cylinder with swivel openings facing each other. Fittings will vary in type and direction depending on your application, refer to your parts section for more details.

Install bearings in the main frame anchor for the swing cylinder. This may already be done for you.

Install the swing cylinder between the boom mounting bracket cylinder anchor and the boom swivel with the pins. Insert roll pins through the top and the bottom hole in the pins.

Now the hoses can be attached from the control valve to the swing cylinder.

PREFORMED TUBE INSTALLATION

Lay booms on floor so the side with the nuts welded on is up. If mounting a ditcher head, only the main boom tube installation is required. Locate all tube clamps and install them loosely in the welded nuts on the left side of the booms.

Arrange the tubes and hoses as outlined in the parts section diagram. Install the smaller tube closest to the boom arm, being careful not to pinch the tubes. Place the large tubes outside of the small tubes. Snug all clamp bolts, but do not tighten. Check all tubes for correct alignment and that none are pinched or bent. The clamp bolts can now be tightened.

SOLENOID BRAKE VALVE

Install a solenoid valve mounting bracket with the supplied hardware. While installing fittings to the brake valve, the electrical coil on the spool must be removed to make room. When reinstalling the coil, it is important to use no more than 5 ft. lbs. (or 60 in. lbs.) torque. Over torque to the coil will result in hydraulic failure of spool.

Assembly Section 2-20

Page 52
Image 52
Tiger Products Co., Ltd CNH T6010-80 Assembly Boom Mounting Bracket, Swivel Bracket Mounting, Preformed Tube Installation

CNH T6010-80 specifications

Tiger Products Co., Ltd has been a prominent player in the construction and engineering equipment sector, and one of their noteworthy offerings is the CNH T6010-80. This product stands out owing to its engineering precision, robust performance, and user-centric design.

The CNH T6010-80 is equipped with a powerful engine that ensures robust performance in various working conditions, making it an ideal choice for contractors and construction professionals. With an output of 80 horsepower, it delivers the right balance of power and efficiency. This makes it suitable for a range of applications, from earthmoving to material handling.

One of the main features of the T6010-80 is its advanced hydraulic system, which provides exceptional lifting capabilities and ensures smooth operation. The integrated hydraulic technology enhances productivity, allowing operators to perform tasks with higher precision and speed. This system also contributes to the machine's versatility, enabling rapid switching between different attachments, which is crucial for dynamic job sites.

The cabin of the T6010-80 is designed with operator comfort in mind. It boasts an ergonomic layout, offering easy access to controls and a spacious environment that reduces fatigue over long working hours. Ensuring occupant safety, the cabin is reinforced, and the visibility from the operator's seat is optimized, allowing for better situational awareness.

Another characteristic worth mentioning is the robust construction of the T6010-80. Built with high-quality materials, it is designed to withstand harsh working conditions. The durability of the machine contributes to a longer lifespan, reducing maintenance costs and increasing return on investment.

Furthermore, Tiger Products Co., Ltd has integrated modern technology into the T6010-80, including features such as GPS and telematics systems. These technologies allow for real-time monitoring of the machine's performance and location, facilitating better fleet management and operational efficiency.

In conclusion, the CNH T6010-80 from Tiger Products Co., Ltd is a powerful, efficient, and versatile machine, ideal for various construction tasks. With its emphasis on performance, operator comfort, and advanced technologies, it exemplifies the brand's commitment to providing reliable and innovative solutions in the engineering equipment industry. Whether for small-scale projects or larger construction undertakings, the T6010-80 delivers the performance professionals need to excel in their work.