OPERATION

To ensure a clean cut, engine speed should be maintained at approximately 1900 – 2200 R.P.M. If the tractor slows to less than 1800 R.P.M., shift to the next lower gear. DO NOT ride the clutch, this will cause premature clutch failure. The engine should not be operated at any time at more than 2400 R.P.M. on the tractor tachometer.

For cutting brush it is usually best to stop the tractor and swivel the boom and mower into foliage. The horizontal positioning action of the boom is designed to position the cutting head and provide a limited pressure relief when excessive pressure is applied to the boom.

DO NOT use excessive force when positioning cutting head into heavy branches or stumps. Damage to the unit may result. It is best to let the cutter head “eat away” slowly at heavy cutting jobs.

If foliage falls on top of mower deck causing tractor to become unstable, move the boom “Forward” and “Out” to relieve tipping of the tractor. Lower mower deck to ground and shut down unit. After

all motion stops, remove foliage from mower deck.

The mower will operate more efficiently in tougher conditions and with less power if the knives are kept sharp. If the mower begins to vibrate, stop the tractor, check for wire wrapped in the spindle or damaged knives. When replacing knives, replace all knives with new knives to ensure proper balance so the mower will not vibrate. Severe vibration will result, if knives with unequal wear are used.

Begin a pass at the top side of the trees and work down with each consecutive pass. When cutting trees and shrubs, use a lower speed to allow the knives time to cut as well as mulch the foliage.

If bystanders approach within 300 feet while mower is in operation turn mower switch “OFF” immediately! After shutdown, never leave the tractor or allow bystanders to approach within 300 FEET of the unit until all motion stops completely.

If cutter shaft jams and stops, turn mower switch to “OFF”, and swivel boom “AFT”. Normally this action will clear the cutter head. If not, roll mower deck until adjacent to the secondary boom, then lower boom to rest mower deck on ground. Shut off the tractor, set parking break, allow all motion to cease. At that point it is safe to leave the tractor and clear the cutter heads manually.

Begin each pass at the top side of the trees and work down with each consecutive pass. Use a low speed to allow the cutting blades time to mulch as well as cut the foliage. When the initial pass has been made, disengage the mower, and return boom to a safe travel position. Return to starting point and make next pass, etc..

After the first day of operation, all bolts should be checked and tightened securely. This should be done periodically to ensure the bolts do not become loose and cause damage to the tractor or mower, or injury to the operator.

Operation Section 3-8

Page 71 Page 73
Page 72
Image 72
Tiger Products Co., Ltd CNH T6010-80 manual Operation
Page 71 Page 73

CNH T6010-80 specifications

Tiger Products Co., Ltd has been a prominent player in the construction and engineering equipment sector, and one of their noteworthy offerings is the CNH T6010-80. This product stands out owing to its engineering precision, robust performance, and user-centric design.

The CNH T6010-80 is equipped with a powerful engine that ensures robust performance in various working conditions, making it an ideal choice for contractors and construction professionals. With an output of 80 horsepower, it delivers the right balance of power and efficiency. This makes it suitable for a range of applications, from earthmoving to material handling.

One of the main features of the T6010-80 is its advanced hydraulic system, which provides exceptional lifting capabilities and ensures smooth operation. The integrated hydraulic technology enhances productivity, allowing operators to perform tasks with higher precision and speed. This system also contributes to the machine's versatility, enabling rapid switching between different attachments, which is crucial for dynamic job sites.

The cabin of the T6010-80 is designed with operator comfort in mind. It boasts an ergonomic layout, offering easy access to controls and a spacious environment that reduces fatigue over long working hours. Ensuring occupant safety, the cabin is reinforced, and the visibility from the operator's seat is optimized, allowing for better situational awareness.

Another characteristic worth mentioning is the robust construction of the T6010-80. Built with high-quality materials, it is designed to withstand harsh working conditions. The durability of the machine contributes to a longer lifespan, reducing maintenance costs and increasing return on investment.

Furthermore, Tiger Products Co., Ltd has integrated modern technology into the T6010-80, including features such as GPS and telematics systems. These technologies allow for real-time monitoring of the machine's performance and location, facilitating better fleet management and operational efficiency.

In conclusion, the CNH T6010-80 from Tiger Products Co., Ltd is a powerful, efficient, and versatile machine, ideal for various construction tasks. With its emphasis on performance, operator comfort, and advanced technologies, it exemplifies the brand's commitment to providing reliable and innovative solutions in the engineering equipment industry. Whether for small-scale projects or larger construction undertakings, the T6010-80 delivers the performance professionals need to excel in their work.
Top Page Image Contents