ASSEMBLY

Run tractor at normal operating RPM to adjust the settings as follows.

Set the dead band compensation potentiometer first.

Set the dead band compensation potentiometer at 50%, or halfway between full clockwise and full counter-clockwise.

Setting Signal Adaptation Potentiometers:

Disconnect the Deutsch connectors from the actuators of the valve. Use a Volt/Ohm meter to measure signal voltage and adjust the signal adaptation potentiometers as needed. Pin #4 is tractor supply voltage. Pin #1 is signal voltage from the joystick, and pin #3 is ground. First measure supply voltage between pins 4 and 3. Then measure signal voltage between pins 1 and 3 while indexing the joystick function fully in both the “A” and “B” port direction. Divide the signal voltage by the supply voltage to get signal voltage as a % of supply voltage. This percentage should not be less than 25% or greater than 75% for the Main Boom, Secondary Boom, or Swivel function. This percentage should not be less than 30% or greater than 62% for the Deck Roll function. Note these initial settings for the Deck Roll function should prevent the spool from shifting into float. After making this first adjustment to deck roll if the spool still goes into float, adjust the “B” port screw additionally counterclockwise.

Reconnect Deutsch connectors on control cables to actuators on Danfoss valve. Run tractor until hydraulic system is at operating temperature. Now refine the adjustments of the signal adaptation potentiometers for both “A” and “B” ports for all proportional functions to achieve the following function times. Note: turning potentiometer clockwise increases the flow or the function speed, and turning them counter- clockwise decreases the flow or the function speed. Note, if during this procedure the trim potentiometer is set to full “counterclockwise” but the function is still too fast, use the mechanical stops at the manual actuator end of the valve section to further limit flow. Turn limit screw in or clockwise to limit flow. The upper limit screw limits flow to “B-port”, and the lower limit screw limits flow to “A-port”. However DO NOT adjust the limit screw on “B-port” of deck roll function. Limiting “B-port” will prevent “float” function.

Assembly Section 2-28

Page 60
Image 60
Tiger Products Co., Ltd CNH T6010-80 manual Set the dead band compensation potentiometer first

CNH T6010-80 specifications

Tiger Products Co., Ltd has been a prominent player in the construction and engineering equipment sector, and one of their noteworthy offerings is the CNH T6010-80. This product stands out owing to its engineering precision, robust performance, and user-centric design.

The CNH T6010-80 is equipped with a powerful engine that ensures robust performance in various working conditions, making it an ideal choice for contractors and construction professionals. With an output of 80 horsepower, it delivers the right balance of power and efficiency. This makes it suitable for a range of applications, from earthmoving to material handling.

One of the main features of the T6010-80 is its advanced hydraulic system, which provides exceptional lifting capabilities and ensures smooth operation. The integrated hydraulic technology enhances productivity, allowing operators to perform tasks with higher precision and speed. This system also contributes to the machine's versatility, enabling rapid switching between different attachments, which is crucial for dynamic job sites.

The cabin of the T6010-80 is designed with operator comfort in mind. It boasts an ergonomic layout, offering easy access to controls and a spacious environment that reduces fatigue over long working hours. Ensuring occupant safety, the cabin is reinforced, and the visibility from the operator's seat is optimized, allowing for better situational awareness.

Another characteristic worth mentioning is the robust construction of the T6010-80. Built with high-quality materials, it is designed to withstand harsh working conditions. The durability of the machine contributes to a longer lifespan, reducing maintenance costs and increasing return on investment.

Furthermore, Tiger Products Co., Ltd has integrated modern technology into the T6010-80, including features such as GPS and telematics systems. These technologies allow for real-time monitoring of the machine's performance and location, facilitating better fleet management and operational efficiency.

In conclusion, the CNH T6010-80 from Tiger Products Co., Ltd is a powerful, efficient, and versatile machine, ideal for various construction tasks. With its emphasis on performance, operator comfort, and advanced technologies, it exemplifies the brand's commitment to providing reliable and innovative solutions in the engineering equipment industry. Whether for small-scale projects or larger construction undertakings, the T6010-80 delivers the performance professionals need to excel in their work.