•Rotatechokeknobto FULLchokeposition(cold enginestart).Ifengineiswarm,placechokeinOFF positioninsteadofFULL.

•Pushprimerbuttontwoorthreetimesforcold enginestart,makingsuretocoverventholein primerbuttonwhenpushingDONOTuseprimerto. restartawarmengineafterashortshutdown.

•Pushstarterbuttontostartengine.

•Whenenginestarts,releasestarterbutton,and

movechokegraduallytoOFF.Ifenginefalters, movechokeimmediatelytoFULLandthen graduallytoOFF.

•Whendisconnectingthepowercord,alwaysunplug

fromthethree-prongreceptaclefirstandthenfrom thesnowthrower.

Recoil Starter

•Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL.

•Push primer button three or four times for cold engine start. DO NOT use primer to restart a warm engine after a short shutdown.

NOTE: Always cover vent hole in primer button when pushing. Additional priming may be necessary for first start if temperature is below 15°F.

•Grasp starter handle and pull rope out slowly, until it pulls slightly harder. Let rope rewind slowly.

•Pull starter handle rapidly. Do not allow handle to

snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle.

•Repeat the previous steps until engine starts.

•As engine warms up, rotate choke knob slowly to OFF position. If engine falters, return to FULL choke, then slowly move to OFF position

ToStopEngine

•Run engine for a few minutes before stopping to help dry off any moisture on the engine.

•To help prevent possible freeze-up of starter, proceed as follows:

Electric Starter:

•Connect power cord to switch box on engine, then to 120 volt AC receptacle. With the engine running, push starter button and spin the starter for several seconds. The unusual sound made by spinning the starter will not harm engine or starter. Disconnect

the power cord from receptacle first, and then from switch box.

Recoil Starter

•With engine running, pull starter rope with a rapid, continuous full arm stroke three or four times.

Pulling the starter rope will produce a loud clattering sound, which is not harmful to the engine or starter.

•To stop engine, move throttle control to "stop" or "off" position.

•Remove ignition key (DO NOT turn key) to prevent unauthorized use of equipment.

NOTE: Do not lose ignition key. Keep it in a safe place. Engine will not start without ignition key.

•Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times.

ToEngageTrackDrive

•With the engine running near top speed, move the shift lever into one of the six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.

•Squeeze the auger control and the augers will turn. Release it and the augers will stop.

•Squeeze drive control and the snow thrower will move. Release it and drive motion will stop.

IMPORTANT:NEVER move shift lever without releasing the drive control. Doing so will cause premature wear on the drive system's friction wheel.

ToEngageAugers

•To engage the augers and start throwing snow, squeeze the auger control against the left handle.

•To disengage power to the augers, release both the auger control and the drive control, if engaged.

The auger control can be locked so you can turn the chute directional control without interrupting the snow throwing process.

Auger Control Test

IMPORTANT:Perform the following test before

operating your snow thrower for the first time and at the start of each winter season.

Check the adjustment of the auger control as follows:

•When the auger control is released and in the disengaged "up" position, the cable should have very little slack. It should NOT be tight.

•In a well-ventilated area, start the snow thrower engine as instructed earlier in this section under the heading Starting Engine. Make sure the throttle is set in the FAST position.

•While standing in the operator's position (behind the snow thrower), engage the auger.

•Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.

•With the engine running in the FAST position and

the auger control in the disengaged "up" position, walk to the front of the machine.

Page 8 Page 10
Page 9
Image 9
Toro 1028, 1130 manual ToEngageTrackDrive, ToEngageAugers, Recoil Starter, Electric Starter, Auger Control Test
Page 8 Page 10

1028, 1130 specifications

The Toro 1130 and 1028 snow throwers are robust machines designed to tackle winter's challenges with ease and efficiency. These models stand out for their power, innovative technologies, and user-friendly features, making them ideal choices for homeowners and professionals alike.

One of the primary features of both the Toro 1130 and 1028 is their powerful engine. The 1130 is equipped with a reliable 302cc engine, while the 1028 boasts a 250cc engine, providing ample power to clear deep snow quickly and effectively. The engines are designed for ease of starting, even in frigid temperatures, thanks to features like the electric start option.

Both models feature Toro's exceptional ClearOut technology, which enhances the snow throwers’ performance by improving the throwing distance and reducing clogging. This technology allows users to tackle heavy, wet snow and create a clear path efficiently. The 11-inch impeller and the rugged auger system are engineered to handle a variety of snow conditions, ensuring optimal clearing performance.

The Toro 1130 and 1028 are designed with user comfort in mind. Both models feature adjustable handle heights, allowing operators of different sizes to find the most comfortable position. The ergonomic handles are equipped with rubber grips that reduce fatigue during extended use. Additionally, their compact design makes them easy to maneuver in tight spaces, such as between cars and along walkways.

Another significant characteristic of these snow throwers is their intuitive controls. The one-hand operation feature allows users to easily control the chute direction and speed while managing the throttle. This functionality provides greater control and efficiency, allowing users to maintain focus on the task at hand.

Durability is also a hallmark of the Toro 1130 and 1028. Constructed from high-quality materials, these machines are built to withstand the rigors of winter. The heavy-duty housing and well-designed components ensure that they can handle tough conditions without compromising performance.

In summary, the Toro 1130 and 1028 snow throwers combine power, technology, and user-friendly features to deliver outstanding snow-clearing capabilities. With reliable engines, innovative throwing technology, ergonomic designs, and durability, these models are excellent choices for anyone looking to conquer winter's worst. Whether for residential or commercial use, Toro's commitment to quality makes these snow throwers a trusted option for snow management.
Top Page Image Contents