Toro 1028, 1130 manual AugerDriveControl

Thedrivecontrolalsolockstheaugercontrolsoyou can turn the chute directionalcontrol without

interruptingthe snowthrowingprocess.If the auger controlis engagedalongwith the drivecontrol,the operatorcan releasethe augercontrol(on the left handle)andtheaugerswillremainengagedRelease. bothcontrolstostoptheaugersandtrackdrive.

IMPORTANT:Alwaysreleasedrivecontrolbefore

changingspeeds.

AugerDriveControl

The auger drive control is located on the left handle. Squeeze the control grip to engage the augers. Release to stop the snow throwing action. (Drive control must also be released.) See Figure 5.

IMPORTANT: Refer to AugerControlTeston page 9 prior to operating your snow thrower. Read and follow all instructions carefully and perform all adjustments to verify your snow thrower is operating safely and properly.

ChuteTilt Control

The distance snow is thrown can be changed by adjusting the angle of the upper chute. Move the chute tilt control forward to decrease the distance, and backwards to increase distance. See Figure 5.

Skid Shoe

The space between the shave plate and the ground can be adjusted by positioning the skid shoes. Refer to Skid ShoeAdjustmenton page 12.

ShiftLever

The shift lever is located in the center of the handle panel and is used to determine both ground speed and direction of travel. It can be moved into any of eight positions. See Figure 5.

Forward

Your snow thrower has six forward (F) speeds, with position number one (1) being the slowest speed.

Reverse

Your snow thrower has two reverse (R) speeds, with position number one (1) being the slowest speed,

IMPORTANT: Always release drive control before changing speeds,

•Counterclockwise to discharge to the right.

Clean-0utTool

The clean-out tool is designed to clear a clogged chute.

Refer to page 10 for instructions on how to properly use it.

WARNING: Never use your hand to clear a clogged chute. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.

Use the clean-out tool or a stick to unclog.

HeatedHandlesSwitch (Model1028)

This switch is located on the right side of the snow thrower dash panel. To activate the heated handles, toggle the switch to the right to generate heat within the handle grips. Toggle the switch to the left to the OFF position after using the snow thrower. See Figure 5.

NOTE: The heated handles grips are a compliment to, not a substitute for, proper cold weather outerwear for the operator's hands. It is recommended that the snow

thrower operator wear gloves/mittens to avoid extremities of winter while operating this equipment.

TrackSteeringControls

The left and right track steering controls are located on the underside of the handles and they are used to assist in steering the snow thrower. Squeeze the right track control when turning right, squeeze the left control when turning left. Operate your snow thrower in open areas until you become familiar with these controls. See Figure 5.

NOTE: It is easier to maneuver a non-running snow thrower with both track steering controls held in simultaneously.

ThrottleControl

The throttle control is located on the engine. It regulates the speed of the engine and will shut off the engine when pushed down completely, See Figure 5,

FuelShut-0ffValve(optionalEquipment)

On models so equipped, the fuel shut-off valve, located under fuel tank, controls fuel-flow from the fuel tank to the engine. See Figure 5.

ChuteDirectionalControl

The chute directional control is located on left side of the snow thrower. See Figure 5.

To change the direction in which snow is thrown, turn chute directional control as follows:

•Clockwise to discharge to the left.

SafetyIgnitionKey

The safety ignition key must be fully inserted and snapped in place before the unit will start. Remove the ignition key to prevent unauthorized use of equipment. See Figure 5.

IMPORTANT: Do NOT attempt to turn the key.