Using the TV/VIDEO button on the TV
Use the TV/VIDEO button on the TV to monitor or change the signal source connected to your TV.
To select the signal source:
Press the TV/VIDEO button on the TV to select either VIDEO 1, VIDEO 2, VIDEO 3, ColorStream, ANT 1, or ANT 2. Repeatedly press the TV/VIDEO button on the TV until the signal source you wish to use displays in purple.
VIDEO 1 |
|
VIDEO 2 | ANT 1 |
VIDEO 3 |
|
COLOR | ANT 2 |
STREAM |
|
TO SELECT PUSH TV/VIDEO
MENU TV/VIDEO VOLUME | CHANNEL |
Menu
TV/Video
Setting up your TV
Adding channels to the TV’s memory
When you press Channel ▲ or ▼ on the TV or remote control, the TV stops only on the channels stored in the TV’s memory.
Note: To tune the TV to a channel not programmed in the TV’s memory, use the Channel Number buttons on the remote control.
Follow the steps below and on the next page to program channels into the TV’s memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area and store them in the TV’s memory. After the channels are stored auto- matically, you can manually add or erase individual channels (see page
13.If you use both
To program channels automatically:
1.Press MENU.
2.Press x or • to highlight the SET UP menu.
3.Press y or z to highlight TV/CABLE.
4.Press x or • to highlight either TV or CABLE, depending on which you use. If you use an antenna, highlight TV. If you use cable, highlight CABLE.
5.Press z to highlight CH PROGRAM.
POWER
LIGHT RECALL
TV
CABLE MUTE TV/VIDEO TIMER
VCR
1 2 3
CH
4 5 6
7 8 9
CH RTN VOL
100 0 ENT
TV/Video Channel 
|
|
|
|
|
|
|
|
| PREFER | C.CAPT |
|
|
|
|
|
|
|
|
|
|
|
|
PICTURE | AUDIO | SET UP |
|
| PICTURE | AUDIO | SET UP | PREFER | C.CAPT |
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LANGUAGE: | [ENGLISH]FRANCAIS |
| LANGUAGE: | [ENGLISH]FRANCAIS | ||||||||||||||||||
|
|
|
|
|
|
|
| ESPANOL |
|
|
|
|
|
|
| ESPANOL | ||||||
ANT1/2: | [ANT1]ANT2 |
| ANT1/2: | [ANT1]ANT2 | ||||||||||||||||||
TV/CABLE: | [TV]CABLE |
| TV/CABLE: | [TV]CABLE | ||||||||||||||||||
CH PROGRAM |
|
|
|
|
| CH PROGRAM |
|
|
|
| ||||||||||||
ADD/ERASE: | [ADD]ERASE |
| ADD/ERASE: | [ADD]ERASE | ||||||||||||||||||
| MORE |
|
|
|
|
|
|
|
|
| MORE |
|
|
|
|
| ||||||
MOVE[ |
|
| ] SELECT[ | ] |
|
|
| MOVE[ | ] START[ | ] |
|
| ||||||||||
6.Press x or • to start automatic channel programming. The TV automatically cycles through every TV or cable channel (depending on which you selected), and stores all active channels in the TV’s memory.
7.When automatic channel programming is complete, the message “CH Programming Completed” appears.
8.Press Channel ▲ or ▼ to view the programmed channels.
.CAPT C
FAV 
RESET
ADV/
PIP CH
MENU
ENTER FAV
ADV/ | EXIT |
PIP CH |
|
Menu
Exit
12