Adding channels to the TV’s memory | Toshiba 43A61 manual

Setting up your TV

Adding channels to the TV’s memory

When you press Channel y or z, your TV will stop only on the channels stored in the TV’s channel memory. Follow the steps below and on the next page to program channels into the TV’s memory.

Programming channels automatically

Your TV can automatically detect all active channels and store them in its memory. After the TV has stored the channels in its memory, you can erase channels or add your favorite channels. If you use both ANT-1 and ANT-2 terminals, you must program channels for each input source.

To program channels automatically:

1.Press MENU, and then press x or • until the SET UP menu appears.

2.Press y or z until TV/CABLE is highlighted.

3.Press x or • to highlight either TV or CABLE, depending on which you use. If you use an antenna, highlight TV; if you use cable, highlight CABLE.

SET UP
LANGUAGE	ENGL I SH
CLOCK SET
ANT 1 / 2	ANT 1
TV / CABLE	TV / CABLE
CH PROGRAM
ADD / ERASE	ADD

4. Press z to select CH PROGRAM.

		SET UP
LANGUAGE			ENGL I SH
CLOCK SET
ANT 1 / 2			ANT 1
TV / CABLE			CABLE
CH PROGRAM
ADD / ERASE			ADD

5.Press x or • to start channel programming. The TV will automatically cycle through all the TV or Cable channels (depending on which you selected), and store all active channels in the channel memory.

While the TV is cycling through the channels, the message “Programming Now—Please Wait” appears.

6.When channel programming is complete, the message “Completed” appears.

7.Press Channel yz to view the programmed channels.

LIGHT RECALL POWER

TV

CABLE MUTE TV/VIDEO TIMER VCR

1	2	3
			CH
4	5	6
7	8	9
		CH RTN	VOL
100	0	ENT
		ADV/
.CAPT	PIP CH		MENU
.CAPT			MENU
C
FAV	ENTER		FAV
RESET		ADV/	EXIT
		ADV/	EXIT

PIP CH

Channel yz

MENU

yzx •

20

Image 20

Toshiba 43A61 Adding channels to the TV’s memory, Programming channels automatically, Press z to select CH Program

Contents

50A61, 50A62 Safety Precautions Dear Customer Important Safety Instructions Installation Service Care Important Safety Information Introduction Exploring your new TV IntroductionWelcome to Toshiba Connecting your TV Connecting a VCR Connecting a cable converter box Connecting a cable converter box and a VCR Connecting a DVD player or satellite receiver and a VCR Two video cables One set of component video cables Connecting two VCRs From Antenna Connecting a camcorder Connecting an audio system Connecting an A/V receiver Connection example of Dolby Pro Logic surround system Using the remote control Preparing the remote control for useInstalling the remote control batteries Using the remote control with a VCR or a cable TV converter Using the Remote Control VCR code table Brand name Code number Cable TV converter code table ABC Learning about the remote control Setting up your TV Press Exit to close an on-screen display instantly Press x or to highlight your desired language Changing the on-screen display languageSelecting the antenna input Press z to select CH Program Adding channels to the TV’s memoryProgramming channels automatically Adding and erasing channels manually Changing channels using SpeedSurfChanging channels Press Exit twice to close the convergence menus Adjusting the color convergencePress x or to display the center convergence menu Using the TV’s features Adjusting the channel settingsSwitching between two channels Programming your favorite channels Using the TV’s Features Labeling channels Channel Number Into the program block mode. See ÒUsing the V-CHIP menuÓ on Watching picture-in-picture PIP Freezing the small picture Switching the main and small picturesChanging the position of the small picture Entering the PIN code If you cannot remember your PIN codeChanging the PIN code Using the V-CHIP menu TV Rating Independent rating system for broadcasters Mpaa Rating Independent rating system for movies Movie ratings you can lock are described as followsLocks menu From the Locks menu, select Locking channels Unlocking programs temporarily To unlock the front panel buttons Select OFF in above Locking video inputsLocking the front panel buttons Adjusting the picture Adjusting the picture qualityTo adjust the picture quality Selecting the picture modes Using the flesh tone feature Using the noise reduction featureTo turn off the flesh tone feature Highlight OFF in above Saving new preferences Selecting the color temperature Resetting your picture adjustments Watching video input Selecting the video input labels Using the closed caption feature Closed caption feature has two optionsTo turn off the closed-caption feature, highlight OFF To view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the clockPress Enter to start the timer To display the time on-screen Press Recall Selecting stereo/SAP broadcasts Adjusting the soundMuting the sound Using the surround sound feature Adjusting the sound quality Resetting your audio adjustments Using the sub-bass system SBS Turning off the built-in speakersTo turn off the SBS Highlight OFF in above To turn on the built-in speakers Highlight on in above Selecting the Audio OUT sound Using the StableSound featureTo turn off the StableSound feature Highlight OFF in above Displaying on-screen information Viewing the demonstration modeSelecting the background of the menu display Understanding the auto power off feature Understanding the last mode memory feature Specifications Appendix Troubleshooting Limited United States Warranty Limited Canada Warranty Appendix Index Channel programming Manufactured by