Toshiba B-670-QQ, B-680-QQ 2.2 OPTIONS

2-2

2. SPECIFICATIONS EO1-33015

2.2 OPTIONS

2.2 OPTIONS

Description

A stop and cut swing cutter

This module strips the label from the back-

ing paper with the take-up block and strip

block.

A 2MB RAM upgrade which enhances the

image handling capability of the printer.

A flash ROM card (1MB and 4MB) for

storing logos, writable characters and for-

mats.

This board enables the following PCMCIA

cards to be used.

* LAN card: 3 COM EtherLink®III (recom-

mended)

* ATA card:Conforming to PC card ATA

standard

* Flash memory card: 4MB card (See Page

10-1.)

Option Name

Cutter module

Strip module

D-RAM PC Board

(B-672 only)

Flash memory card

(B-672 only)

PCMCIA interface

board

(B-682 only)

Type

B-4208-QM

B-4908-H-QM

FMBC0067801

B-8700-PC-QM

Source

See NOTE 1.

See NOTE 1.

See NOTE 2.

See NOTE 3.

See NOTE 1.

NOTES:1. Available from your nearest TOSHIBA TEC representative or TOSHIBA TEC Head

Quarters.

2. Available from TOSHIBA TEC Parts Center.

3. When purchasing flash memory card locally, select one having the specifications described

at page 9-1.

Contents

Main Page Safety Summary WARNING Meanings of Each Symbol CAUTION Precautions Request Regarding Maintenance TABLE OF CONTENTS CAUTION: 1. INTRODUCTION 1.1 APPLICABLE MODEL 1.2 ACCESSORIES 2. SPECIFICATIONS 2.1 PRINTER Data Matrix 2.2 OPTIONS 2-3 2. SPECIFICATIONS Tag paper plus inter label gap length 2.4 RIBBON E Type Spool type Width 115 mm ~ 185 mm (See NOTE 5.) Length 300 m Outer diameter 72 mm (max.) 2.3 MEDIA Fig. 2-1 3. OVERVIEW 3.1 FRONT/REAR VIEW Fig. 3-1 Rear View Fig. 3-2 4. DIP SWITCH FUNCTIONS (B-672 only) The DIP switches are located to the right of the Guide Wheel. (2) DIP SW 1 NOTES: The Shaded settings are the factory default settings. "OFF" means "OPEN". 4. DIP SWITCH FUNCTIONS (B-672 only) 5. SET UP PROCEDURE 5.1 REQUIREMENTS FOR OPERATION NOTE:Use an RS-232C cable with imperial (inch) connector securing screws. Interface Cables RS-232C Cable description 6. INSTALLING THE PRINTER 6.1 CONNECTING THE POWER CORD AND CABLES NOTES: Different cables cannot be used at the same time. 6.2 HOLDER STAND INSTALLATION Turn the POWER SWITCH to OFF before connecting the power cord or cables. 7. LOADING THE RIBBON NOTE: When removing the ribbon, be careful not to snag the ribbon on the part . . CAUTION: When using labels ensure that the head lever is set to position 8. LOADING THE MEDIA NOTE: Set in the bushes of the Holder Shaft into notches of the Holder Stand securely. An easy way to set the black mark sensor position Setting the feed gap sensor position Page CAUTION: When using labels ensure that the head lever is set to position . 9. INSERTING THE OPTIONAL FLASH MEMORY CARD (B-672 only) 10. INSERTING THE OPTIONAL PCMCIA CARD (B-682 only) 11. CARE/HANDLING OF THE MEDIA AND RIBBON 12. GENERAL MAINTENANCE 12.1 CLEANING Page 12.2 UNDER THE MEDIA GUIDES 12.3 COVERS AND PANELS 12.4 REMOVING JAMMED MEDIA Cleaning the Cutter Unit Cleaning the strip unit Be sure to turn the power off before cleaning the strip unit. 12.5 THRESHOLD SETTING Threshold setting procedure 13. TROUBLESHOOTING Page NOTE: If an error is not cleared by pressing the