Input & Output Specifications

INPUT SPECIFICATIONS

0dB is referenced to 0.775V RMS.
Input
CHANNEL IN
BAL –60
BAL –40
BAL –20
UN-BAL
ACCESSORY
(RCV)
STEREO IN
AUX
PHONO
AUX ECHO IN
SUB IN
Actual
Load
Impedance
550 ohms
800 ohms
900 ohms
25k ohms
10k ohm s
10k ohms
47k ohms
10k ohms
10k ohms
For Use
With
Nominal
50 to 600
ohms
10k ohms
10k ohms
10k ohms
4 7k ohms
10k ohms
10k ohms
Sensitivity*
–80dB (0.08mV)
–60dB (0.78mV)
–40dB (7.8mV)
–50dB (2.5mV)
-20dB (78mV)
–40dB (7.8mV)
–70dB (0.25mV)
-40dB (7.8mV)
–10dB (250mV)
Input Level (Trim "0" to Trim "–30")
Nominal
–60dB (0.78mV) to –30dB (25mV)
–40dB (7.8mV) to –10dB (250mV)
–20dB (78mV) to +10dB (2.5V)
–30dB (25mV) to 0dB (775mV)
–0dB (775mV)
–20dB (78mV)
–50dB (2.5mV)
-20dB (78mV)
+4dB (1.23mV)
MAX. Before Clip
–40dB (7.8mV) to –10dB (250mV)
–20dB (78mV) to +10dB (2.5V)
0dB (775V) to +30dB (25V)
–10dB (250mV) to +20dB (7.8V)
20dB (7.8mV)
+10dB (2.5V)
–20dB (78mV)
0dB (775mV)
+24dB (12.3mV)
Connector
XLR-3-31
type**
PHONE JACK
3P PHONE
JACK***
RCA
PIN JACK
PHONE JACK
PHONE JACK

OUTPUT SPECIFICATIONS

0dB is referenced to 0.775V RMS.
Output
PGM L
LI N E O U T PGM R
FBlFB2
EC H O SE N D +4
-20
REC OUT
ACCESSORY (SEND)
PHONES
Actual Source Impedance
100 ohms
90 ohms
64 ohms
1k ohms
1k ohms
18 ohms
For Use With Nominal
600 ohms
600 ohm s
10k ohms
10k ohms
8 ohms or higher
Output Level
Nominal
+4dB (1.23V)
+4dB (1.23V)
–20dB (78mV)
–10dB (250mV)
0dB (775mV)
75mW/8 ohms,
0dB (775mV)
MAX Before Clip
+20dB (7.8V)
+20dB (7.8V)
-4dB (490mV)
+10dB (2.5V)
+20dB (7.8V)
370mW/8 ohms,
+7dB (1.7V)
Connector
XLR-3-32
type**
and
PHONE JACK
PHONE JACK
PHONE JACK
RCA PIN JACK
3P PHONE JACK***
STEREO
PHONE JACK****
*Sensitivity is the level required to produce a nominal speaker output level.
**All XLR type connectors are floating, balanced and transformer-isolated.
***ACCESSORY jacks (3P PHONE JACK) are wired: Tip=Receive, Ring=Send and Sleeve =Common
****Stereo phone jack is wired: Tip=Left, Ring=Right and Sleave=Common
Note:
As is described in the beginning of the operation manual, the XLR type connectors of the RX-208, RX-212 and RX-216 are wired as follows.
Pin No. 1 — Ground
Pin No. 2 — Cold (Low)
Pin No. 3 — Hot (High)
Specifications are subject to change without notice.

Caution:

The fuse rating for 120V AC operation is 2 amps., and 1 amp. for 220/240V AC operation. The fuse must always be replaced
with same typ e and rating.

-

15

-