Manuals / Transcend Information / Computer Equipment / Computer Hardware

Transcend Information TS2G-8GCF266 manual Transfer Function, Table Pcmcia Mode I/O Function

Models: TS2G-8GCF266

1 80

Download 80 pages 60.13 Kb

Page 39

TS2G~8GCF266		266X CompactFlash Card

I/O Transfer Function

The I/O transfer to or from the CompactFlash Storage or CF+ Card can be either 8 or 16 bits. When a 16 bit accessible port is addressed, the signal -IOIS16 is asserted by the CompactFlash Storage or CF+ Card. Otherwise, the -IOIS16 signal is de-asserted. When a 16 bit transfer is attempted, and the -IOIS16 signal is not asserted by the CompactFlash Storage or CF+ Card, the system shall generate a pair of 8 bit references to access the word‘s even byte and odd byte. The CompactFlash Storage Card permits both 8 and 16 bit accesses to all of its I/O addresses, so -IOIS16 is asserted for all addresses to which the CompactFlash Storage responds. CF+ cards may or may not allow 16 bit register accesses and thus shall assert -IOIS16 as required. The CompactFlash Storage and CF+ Card may request the host to extend the length of an input cycle until data is ready by asserting the -WAIT signal at the start of the cycle.

Table : PCMCIA Mode I/O Function

Transcend Information Inc.

39

Image 39

Transcend Information TS2G-8GCF266 manual Transfer Function, Table Pcmcia Mode I/O Function

Contents

Placement Features DimensionsDescription Transcend Block Diagram Pin Assignments and Pin Type TS2G~8GCF266 Signal Description TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Electrical Specification Output Drive Type Output Drive Characteristics Signal Interface Pull-up pin 45 BVD2 to avoid sensing their batteries as Low TS2G~8GCF266266X CompactFlash CardUltra DMA Electrical Requirements Series termination required for Ultra DMA operationTable Typical Series Termination for Ultra DMA Ultra DMA Mode Cabling Requirement Attribute Memory Read Timing Specification TS2G~8GCF266 Common Memory Read Timing Specification Common Memory Write Timing Specification Input Read Timing Specification TS2G~8GCF266 Output Write Timing Specification TS2G~8GCF266 True IDE PIO Mode Read/Write Timing Specification TS2G~8GCF266 Table Ultra DMA Data Burst Timing True IDE Ultra DMA Mode Read/Write Timing SpecificationTS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Card Configuration Single Function CF+ CardsMultiple Function CF+ Cards Table CF+ Card Register and Memory Space Decoding Table CF+ Card Configuration Registers DecodingAttribute Memory Function Attribute Memory FunctionConfiguration Option Register Base + 00h in Attribute Memory TS2G~8GCF266 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Transfer Function Table Pcmcia Mode I/O FunctionTable Common Memory Function Common Memory Transfer FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Table Primary and Secondary I/O Decoding Primary and Secondary Address ConfigurationsTable Contiguous I/O Decoding Contiguous I/O Mapped AddressingMemory Mapped Addressing True IDE Mode AddressingData Register Address 1F0h170hOffset 0,8,9 CF-ATA RegistersCylinder Low LBA 15-8 Register Address 1F4h174h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Count Register Address 1F2h172h Offset Sector Number LBA 7-0 Register Address 1F3h173h OffsetTS2G~8GCF266 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set Check Power Mode 98h or E5h Erase Sectors C0h Execute Drive Diagnostic 90hFormat Track 50h Flush Cache E7hIdentify Device Ech TS2G~8GCF266 Word 0 General Configuration Word 49 Capabilities Bit 13 Standby Timer Word 1 Default Number of CylindersWord 3 Default Number of Heads Word 6 Default Number of Sectors per TrackCurrent Number of Cylinders, Heads, Sectors/Track Multiple Sector SettingTotal Sectors Addressable in LBA Mode Translation Parameters ValidWord 68 Minimum PIO transfer cycle time with Iordy Words 82-84 Features/command sets supportedWord 65 Minimum Multiword DMA transfer cycle time Recommended Multiword DMA transfer cycle timeWords 85-87 Features/command sets enabled Word 89 Time required for Security erase unit completion Word 88 Ultra DMA Modes Supported and SelectedAdditional Requirements for CF Advanced Timing Modes Word 91 Advanced power management level valueWord 160 Power Requirement Description Word 128 Security Status Bit 8 Security LevelTS2G~8GCF266 Idle 97h or E3h Idle Immediate 95h or E1h Initialize Drive Parameters 91hNOP 00h Read DMA C8h Read Long Sector 22h or 23h Read Buffer E4hTS2G~8GCF266 Recalibrate 1Xh Request Sense 03h Seek 7Xh Set Features EFh Feature Supported TS2G~8GCF266 Translate Sector Information Standby Immediate 94h or E0h Translate Sector 87hWear Level F5h Write Buffer E8h Write DMA CAh TS2G~8GCF266 TS2G~8GCF266 Error Posting Smart Command Set Smart Command Set Smart Feature Register ValuesS. Table Capacity Decription Smart Data Structure