Identify Device Ech | Transcend Information TS2G-8GCF266 instruction

TS2G~8GCF266		266X CompactFlash Card

Identify Device – Ech

The Identify Device command enables the host to receive parameter information from the CompactFlash Storage Card. This command has the same protocol as the Read Sector(s) command. The parameter words in the buffer have the arrangement and meanings defined in Table as below. All reserved bits or words are zero. Hosts should not depend on Obsolete words in Identify Device containing 0. Table 47 specifies each field in the data returned by the Identify Device Command. In Table as below, X indicates a numeric nibble value specific to the card and aaaa indicates an ASCII string specific to the particular drive.

Transcend Information Inc.

56

Image 56

Transcend Information TS2G-8GCF266 manual Identify Device Ech

Contents

Description Placement FeaturesDimensions Transcend Block Diagram Pin Assignments and Pin Type TS2G~8GCF266 Signal Description TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Electrical Specification Output Drive Type Output Drive Characteristics Signal Interface TS2G~8GCF266266X CompactFlash Card Pull-up pin 45 BVD2 to avoid sensing their batteries as Low Table Typical Series Termination for Ultra DMA Ultra DMA Electrical RequirementsSeries termination required for Ultra DMA operation Ultra DMA Mode Cabling Requirement Attribute Memory Read Timing Specification TS2G~8GCF266 Common Memory Read Timing Specification Common Memory Write Timing Specification Input Read Timing Specification TS2G~8GCF266 Output Write Timing Specification TS2G~8GCF266 True IDE PIO Mode Read/Write Timing Specification TS2G~8GCF266 True IDE Ultra DMA Mode Read/Write Timing Specification Table Ultra DMA Data Burst Timing TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Multiple Function CF+ Cards Card ConfigurationSingle Function CF+ Cards Table CF+ Card Configuration Registers Decoding Table CF+ Card Register and Memory Space Decoding Attribute Memory Function Attribute Memory Function Configuration Option Register Base + 00h in Attribute Memory TS2G~8GCF266 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Table Pcmcia Mode I/O Function Transfer Function Common Memory Transfer Function Table Common Memory Function True IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Primary and Secondary Address Configurations Table Primary and Secondary I/O Decoding Contiguous I/O Mapped Addressing Table Contiguous I/O Decoding True IDE Mode Addressing Memory Mapped Addressing CF-ATA Registers Data Register Address 1F0h170hOffset 0,8,9 Feature Register Address 1F1h171h Offset 1, 0Dh Write Only Sector Count Register Address 1F2h172h OffsetSector Number LBA 7-0 Register Address 1F3h173h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h Offset TS2G~8GCF266 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set Check Power Mode 98h or E5h Execute Drive Diagnostic 90h Erase Sectors C0h Flush Cache E7h Format Track 50h Identify Device Ech TS2G~8GCF266 Word 0 General Configuration Word 1 Default Number of Cylinders Word 3 Default Number of HeadsWord 6 Default Number of Sectors per Track Word 49 Capabilities Bit 13 Standby Timer Multiple Sector Setting Total Sectors Addressable in LBA ModeTranslation Parameters Valid Current Number of Cylinders, Heads, Sectors/Track Words 82-84 Features/command sets supported Word 65 Minimum Multiword DMA transfer cycle timeRecommended Multiword DMA transfer cycle time Word 68 Minimum PIO transfer cycle time with Iordy Words 85-87 Features/command sets enabled Word 88 Ultra DMA Modes Supported and Selected Word 89 Time required for Security erase unit completion Word 91 Advanced power management level value Word 160 Power Requirement DescriptionWord 128 Security Status Bit 8 Security Level Additional Requirements for CF Advanced Timing Modes TS2G~8GCF266 Idle 97h or E3h NOP 00h Idle Immediate 95h or E1hInitialize Drive Parameters 91h Read Buffer E4h Read DMA C8h Read Long Sector 22h or 23h TS2G~8GCF266 Recalibrate 1Xh Request Sense 03h Seek 7Xh Set Features EFh Feature Supported TS2G~8GCF266 Standby Immediate 94h or E0h Translate Sector 87h Translate Sector Information Wear Level F5h Write Buffer E8h Write DMA CAh TS2G~8GCF266 TS2G~8GCF266 Error Posting S. Table Capacity Smart Command SetSmart Command Set Smart Feature Register Values Smart Data Structure Decription