Manuals / Transition Networks / Computer Equipment / Switch

Transition Networks SM24-100SFP-AH Desktop or Shelf Mounting, 2. Installing the Switch in a Rack

Models: SM24-100SFP-AH

1 60

Page 31

Figure 3-2. Installing the Switch in a Rack

Mounting 3

2.Mount the device in the rack, using four rack-mounting screws (not provided). Be sure to secure the lower rack-mounting screws first to prevent the brackets being bent by the weight of the switch.

Figure 3-2. Installing the Switch in a Rack

3.If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, mount them in the rack, one below the other, in any order.

5.If also installing an RPS, mount it in the rack below the other devices.

Desktop or Shelf Mounting

1.Attach the four adhesive feet to the bottom of the first switch.

Figure 3-3. Attaching the Adhesive Feet

2.Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow.

3-3

Page 31

Image 31

Transition Networks SM24-100SFP-AH manual Desktop or Shelf Mounting, 2. Installing the Switch in a Rack

Contents

SM24-100SFP-AH Fast Ethernet Switch Installation GuidePage Installation Guide Fast Ethernet SwitchLayer 2 Workgroup Switch SM24-100SFP-AH E082008-DT-R01 150200069500A CE Mark Declaration of Conformance for EMI and Safety EEC Compliances and Safety WarningsFCC - Class A according to EN 61000-4-111994 95% Reduction @10 ms, 30% Reduction @500 ms, 95% Reduction @5000 msFrance and Peru only Safety ComplianceWarning Fiber Optic Port Safety Warnhinweis Faseroptikanschlüsse - Optische SicherheitPower Cord Set La prise femelle de branchement doit être du type à mise à la terre France et Pérou uniquement18, ouAWG No. 16 pour un cable de longueur inferieure a` 2 metres Le cordon doit être en mesure d’acheminer un courant nominal d’auWarnings and Cautionary Messages Documentation Environmental StatementEnd of Product Life Span Manufacturing MaterialsRevision History PurposeAudience ConventionsChapter 2 Network Planning ContentsChapter 3 Installing the Switch Chapter 1 IntroductionChapter 4 Making Network Connections Tables Figures Overview Chapter 1 IntroductionFigure 1-1. SM24-100SFP-AH Front and Rear Panels SFP Slots Switch ArchitectureDescription of Hardware Network Management OptionsCondition Port and System Status LEDsFigure 1-2. SM24-100SFP-AH Port Status LEDs Table 1-1 SM24-100SFP-AH Port Status LEDsFigure 1-3. System Status LED Table 1-2 System Status LEDs System self-diagnostic test successfully completedThe backup power supply is plugged in but faulty, such as a OK DiagnosticExpandability Features and BenefitsPower Supply Sockets ConnectivitySupports Telnet, SNMP/RMON and Web-based interface Management“At-a-glance” LEDs for easy troubleshooting Network management agent Manages switch in-band or out-of-bandChapter 2 Network Planning Introduction to SwitchingCollapsed Backbone Application ExamplesFigure 2-1. Collapsed Backbone Figure 2-2. Network Aggregation Plan Network Aggregation PlanFigure 2-3. Remote Connection with Fiber Cable Remote Connection with Fiber CableFigure 2-4. Making VLAN Connections Making VLAN ConnectionsApplication Notes Selecting a Site Chapter 3 Installing the SwitchEquipment Checklist Package ContentsTo rack-mount devices MountingOptional Rack-Mounting Equipment Rack MountingFigure 3-2. Installing the Switch in a Rack Desktop or Shelf MountingFigure 3-3. Attaching the Adhesive Feet Figure 3-4. Inserting an SFP Transceiver into a Slot Installing an Optional SFP TransceiverFigure 3-6. Serial Port RJ-45 Pin-Out Connecting to a Power SourceConnecting to the Console Port Figure 3-5. Power SocketsDefault Baud rate-9,600 bps Character Size-8 Characters Parity-None Wiring Map for Serial CableNo other pins are used The serial port’s configuration requirements are as followsTwisted-Pair Devices Connecting Network DevicesConnecting to PCs, Servers, Hubs and Switches Chapter 4 Making Network ConnectionsFigure 4-2. Network Wiring Connections Network Wiring ConnectionsFigure 4-3. Making Fiber Port Connections Fiber Optic SFP DevicesConnector Connectivity Rules1000BASE-T Cable Requirements 1000 Mbps Gigabit Ethernet Collision DomainTable 4-4. Maximum 1000BASE-LH Gigabit Ethernet Cable Length 100 Mbps Fast Ethernet Collision Domain10 Mbps Ethernet Collision Domain ConnectorCable Labeling and Connection Records Table A-1. Troubleshooting Chart Appendix A TroubleshootingDiagnosing Switch Indicators Diagnosing Power Problems with the LEDsInstallation Power and Cooling ProblemsIn-Band Access Figure B-1. RJ-45 Connector Pin Numbers Appendix B CablesTwisted-Pair Cable and Pin Assignments 10BASE-T/100BASE-TX Pin AssignmentsFigure B-2. Straight-through Wiring Straight-Through WiringCrossover Wiring MDI Signal NameMDI-X Signal Name 1000BASE-T Pin AssignmentsFigure B-3. Crossover Wiring MDI Signal NameAdjusting Existing Category 5 Cabling to Run 1000BASE-T Cable Testing for Existing Category 5 CableAppendix C Supported SFP Transceivers C Supported SFP Transceivers Weight Appendix D SpecificationsPhysical Characteristics Switching DatabasePower Supply Switch FeaturesManagement Features TemperatureEmissions StandardsCompliances SafetyD Specifications Glossary Glossary-2 GlossarySeparate LAN or collision domain Virtual LAN VLAN Transmission Control Protocol/Internet Protocol TCP/IPNumerics IndexIndex-2 IndexPage SM24-100SFP-AH E082008-DT-R01 150200069500A