Manuals / Transition Networks / Computer Equipment / Switch

Transition Networks SM24-100SFP-AH manual Purpose, Audience, Conventions, Revision History

Models: SM24-100SFP-AH

1 60

Page 12

About This Guide

Purpose

This guide details the hardware features of this device, including the physical and performance-related characteristics, and how to install it.

Audience

The guide is intended for use by network administrators who are responsible for installing and setting up network equipment; consequently, it assumes a basic working knowledge of LANs (Local Area Networks).

Conventions

The following conventions are used throughout this guide to show information:

Note: Emphasizes important information or calls your attention to related features or instructions.

Caution: Alerts you to a potential hazard that could cause loss of data, or damage the system or equipment.

Warning: Alerts you to a potential hazard that could cause personal injury.

Revision History

This section summarizes the changes in each revision of this guide.

August 2008 Revision

This is the first revision of this guide.

viii

Page 12

Image 12

Transition Networks SM24-100SFP-AH manual Purpose, Audience, Conventions, Revision History, About This Guide

Contents

Fast Ethernet Switch Installation Guide SM24-100SFP-AHPage Fast Ethernet Switch Installation GuideLayer 2 Workgroup Switch SM24-100SFP-AH E082008-DT-R01 150200069500A Compliances and Safety Warnings CE Mark Declaration of Conformance for EMI and Safety EECFCC - Class A Reduction @500 ms, 95% Reduction @5000 ms according to EN 61000-4-111994 95% Reduction @10 ms, 30%Safety Compliance Warning Fiber Optic Port SafetyWarnhinweis Faseroptikanschlüsse - Optische Sicherheit France and Peru onlyPower Cord Set France et Pérou uniquement 18, ouAWG No. 16 pour un cable de longueur inferieure a` 2 metresLe cordon doit être en mesure d’acheminer un courant nominal d’au La prise femelle de branchement doit être du type à mise à la terreWarnings and Cautionary Messages Environmental Statement End of Product Life SpanManufacturing Materials DocumentationPurpose AudienceConventions Revision HistoryContents Chapter 3 Installing the SwitchChapter 1 Introduction Chapter 2 Network PlanningChapter 4 Making Network Connections Tables Figures Chapter 1 Introduction OverviewFigure 1-1. SM24-100SFP-AH Front and Rear Panels Switch Architecture Description of HardwareNetwork Management Options SFP SlotsPort and System Status LEDs Figure 1-2. SM24-100SFP-AH Port Status LEDsTable 1-1 SM24-100SFP-AH Port Status LEDs ConditionSystem self-diagnostic test successfully completed The backup power supply is plugged in but faulty, such as aOK Diagnostic Figure 1-3. System Status LED Table 1-2 System Status LEDsFeatures and Benefits Power Supply SocketsConnectivity ExpandabilityManagement “At-a-glance” LEDs for easy troubleshooting Network management agentManages switch in-band or out-of-band Supports Telnet, SNMP/RMON and Web-based interfaceIntroduction to Switching Chapter 2 Network PlanningApplication Examples Collapsed BackboneFigure 2-1. Collapsed Backbone Network Aggregation Plan Figure 2-2. Network Aggregation PlanRemote Connection with Fiber Cable Figure 2-3. Remote Connection with Fiber CableMaking VLAN Connections Figure 2-4. Making VLAN ConnectionsApplication Notes Chapter 3 Installing the Switch Equipment ChecklistPackage Contents Selecting a SiteMounting Optional Rack-Mounting EquipmentRack Mounting To rack-mount devicesDesktop or Shelf Mounting Figure 3-2. Installing the Switch in a RackFigure 3-3. Attaching the Adhesive Feet Installing an Optional SFP Transceiver Figure 3-4. Inserting an SFP Transceiver into a SlotConnecting to a Power Source Connecting to the Console PortFigure 3-5. Power Sockets Figure 3-6. Serial Port RJ-45 Pin-OutWiring Map for Serial Cable No other pins are usedThe serial port’s configuration requirements are as follows Default Baud rate-9,600 bps Character Size-8 Characters Parity-NoneConnecting Network Devices Connecting to PCs, Servers, Hubs and SwitchesChapter 4 Making Network Connections Twisted-Pair DevicesNetwork Wiring Connections Figure 4-2. Network Wiring ConnectionsFiber Optic SFP Devices Figure 4-3. Making Fiber Port ConnectionsConnectivity Rules 1000BASE-T Cable Requirements1000 Mbps Gigabit Ethernet Collision Domain Connector100 Mbps Fast Ethernet Collision Domain 10 Mbps Ethernet Collision DomainConnector Table 4-4. Maximum 1000BASE-LH Gigabit Ethernet Cable LengthCable Labeling and Connection Records Appendix A Troubleshooting Diagnosing Switch IndicatorsDiagnosing Power Problems with the LEDs Table A-1. Troubleshooting ChartPower and Cooling Problems InstallationIn-Band Access Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Figure B-1. RJ-45 Connector Pin NumbersStraight-Through Wiring Crossover WiringMDI Signal Name Figure B-2. Straight-through Wiring1000BASE-T Pin Assignments Figure B-3. Crossover WiringMDI Signal Name MDI-X Signal NameCable Testing for Existing Category 5 Cable Adjusting Existing Category 5 Cabling to Run 1000BASE-TAppendix C Supported SFP Transceivers C Supported SFP Transceivers Appendix D Specifications Physical CharacteristicsSwitching Database WeightSwitch Features Management FeaturesTemperature Power SupplyStandards CompliancesSafety EmissionsD Specifications Glossary Glossary Glossary-2Separate LAN or collision domain Transmission Control Protocol/Internet Protocol TCP/IP Virtual LAN VLANIndex NumericsIndex Index-2Page SM24-100SFP-AH E082008-DT-R01 150200069500A