Tripp Lite PVINT375 Troubleshooting, Specifications, Model, Output Power Maximum Continuous Watts

Troubleshooting

Please check the following before sending the Inverter in for service:

Symptom	Problem	Correction
Alarm sounds.	Low battery voltage (<10.5 V).	Turn Inverter OFF and run engine to
		recharge vehicle battery.
	Output overload.	Turn Inverter OFF and remove overload by
		unplugging high-wattage devices. Load
		should not exceed your Inverter's maximum
		continuous output power (see Specifications).
Inverter does not turn ON when	Automatic Inverter shutdown due	Turn Inverter OFF and run engine to
power switch is turned ON.	to low battery voltage (<10V).	recharge vehicle battery.
	Automatic Inverter shutdown due	Turn Inverter OFF and remove overload by
	to output overload.	unplugging high-wattage devices. Load
		should not exceed your Inverter’s maximum
		continuous output power (see Specifications).
	Blown fuse.	Replace fuse with standard automotive fuse
		of identical amperage (see Specifications).
Inverter is unable to power	Battery running low. Low battery	Turn Inverter OFF and run engine to
connected equipment.	voltage reduces Inverter power	recharge vehicle battery.
	output.
	Connected equipment load	Turn Inverter OFF and remove overload by
	exceeds Inverter’s maximum	unplugging high-wattage devices. Load
	continuous output power.	should not exceed your Inverter's maximum
		continuous output power (see Specifications).
Connected equipment experiences	Loose connections.	Check and secure all connections.
audio/video distortion.
	Audio/video interference.	Reposition equipment antennas and Inverter.

Specifications

Model:	PVINT375
Output Power (Maximum Continuous Watts)*:	375
Output Power (Peak Watts)**:	600
Input Voltage (DC):	12V nominal (10-15V)
Output Voltage (AC)/Frequency:	230V / 50 Hz. nominal
Output Waveform:	PWM Sine Wave
Low Battery Voltage Alarm (Volts):	10.5V
Low Battery Voltage Shutdown (Volts):	10V
AC Outlets:	1
Circuit Protection (DC Overload):	40-amp fuse (external)

*Maximum output power (continuous or peak) only available when vehicle battery is properly charged. Run vehicle engine often to maintain proper charge.

**Peak Output Power is instantaneous. The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.

Typical Runtimes Before Battery Recharge

Although you can operate your Inverter with your vehicle engine off, best results are usually attained with the engine running. Since the Inverter converts electrical energy (and doesn’t produce it), the Inverter’s performance is relative to the condition of your vehicle’s electrical system (battery, alternator and wiring). If other loads (air conditioner, heater, lights, etc.) are also using power, you may get less runtime.

	With Typical	With Typical	With Typical
	Compact Vehicle (4 cylinder)	Mid-Size Vehicle (6 cylinder)	Full-Size Vehicle (8 cylinder)
	Battery, Alternator	Battery, Alternator	Battery, Alternator
Model: PVINT375	& Wiring	& Wiring	& Wiring
1/2 Load (engine on/engine off)	continuous/1-2 hours	continuous/2-3 hours	continuous/3-6 hours
Full Load* (engine on/engine off)	continuous/30 min-1 hour	continuous/1-2 hours	continuous/2-3 hours

Vehicle Electrical System Limitations

NOTE: Due to the limitations of certain vehicles’ 12V DC lighter/accessory outlet electrical systems, you may not be able to continuously run a full load (375 watts) from your PVINT375. If you regularly blow fuses, it may indicate your vehicle is not adequately wired to support a PVINT375 as it is designed. In this case, consult vehicle manufacturer recommendations for rewiring from the fuse block or battery with appropriate wiring (8 - 10 gauge) and fusing (at least 40 amp).

3