Feature Identification
Identify the premium features on your specific model and quickly locate instructions on how to maximize their use.
1 Configuration DIP Switches: optimize Inverter/Charger operation depending on your application. See Configuration section for setting instructions.
2Operating Mode Switch: controls Inverter/Charger operation. The “AUTO/REMOTE” setting ensures your equipment receives constant, uninterrupted AC power. It also enables the Inverter/Charger to be remotely monitored and controlled with an optional remote module (Tripp Lite model APSRM4, sold separately or included with select models). The “CHARGE ONLY” setting allows your batteries to return to full charge faster by turning the inverter off which halts battery discharging. See Operation section for setting instructions.
3“LINE”, “INVERT”, “LOAD” LEDs: intuitive “traffic light” signals show whether the Inverter/Charger is operating from AC line power or DC battery power. It also warns you if the connected equipment load is too high. See Operation section for instructions on reading the indicator lights.
4“BATTVOLT/CHRGCURR” LEDs: these three lights will turn ON in several sequences to show two separate operational condi- tions depending on the position of the Operating Mode Switch. See Operation section for instructions on reading indicator lights.
5DC Power Terminals: connect to your battery terminals. See Battery Connection section for instructions.
6Ground Fault Interrupter (GFI) AC Receptacles (not on hardwire models): allow you to connect equipment that would normally be plugged into a utility outlet. They feature ground fault interrupter switches that trip if there is excessive current on the ground safety wire.
7AC Input Cord (not on hardwire models): connects the Inverter/Charger to any source of utility- or
8 Hardwire AC Input/Output Terminals (not on corded models): securely connect the Inverter/Charger to vehicle or facility electrical system input and recommended GFI receptacle output. See AC Input/Output Connection section for instructions.
9Resettable Circuit Breaker: protect your Inverter/Charger against damage due to overload. See Operation section for resetting instructions.
10Remote Control Module Connector: allows remote monitoring and control with an optional module (Tripp Lite model APSRM4, sold separately or included with select models). See remote module owner’s manual for connection instructions.
11Battery Charge Conserver (Load Sense) Dial (not on 612 models): conserves battery power by setting the
12Main Ground Lug: properly grounds the Inverter/Charger to vehicle grounding system or to earth ground. See Configuration section for instructions.
13
14Hardwire AC Input/Output Cover Plate
15Battery Temperature Sensing Connector (not on 612 models): prolongs battery life by adjusting charge based on battery tem- perature. Use with cable (included on select models). See Configuration section for details.
16Automatic Generator Start Connector (not on 612 models): automatically cycles generator based on battery voltage. Use with
13 | 1* | 4 | 10 | 3 | 2 | 11† | 13 | 1 | 4 | 10 | 3 | 2 | 11 |
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
| 15 | Side Mounted, | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| 15† |
|
|
|
|
|
|
| Not Shown |
|
|
|
|
|
| Side Mounted, |
|
|
|
|
| 16 | Side Mounted, | |
|
|
|
|
|
|
| Not Shown |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| Not Shown |
|
|
| 16† Side Mounted, |
|
|
|
|
|
|
|
| Not Shown |
| “FOR USE WITH COPPER WIRE ONLY” | 9 | ||
|
|
| 9 |
| HOT | IN |
| |
|
|
|
|
|
| |||
|
|
|
| NEUTRAL | IN |
| ||
|
|
| 6 |
|
| |||
|
|
|
| GROUND | IN |
| ||
|
|
|
|
| GROUND | OUT |
| |
|
|
|
|
| HOT | OUT |
|
|
|
|
|
|
| NEUTRAL | OUT |
| |
Front View (Corded Models) | 5 | 7 | 12** | 5 | 8 | 14 |
| |
* 612 models have only one set of DIP Switches. ** Select models include | Front View (Single Input/Output Hardwire Models) |
|
|
| ||||
5
12
13 | 1 | 4 | 10 | 3 | 2 | 11 |
15 
16
9
8
12
Front View (Dual Input/Output Hardwire Models)
Rear View (Single Input/Output Hardwire Models and Select Corded Models)
4R
