Executing a Zero Turn

WARNING: When executing a zero turn, the tractor MUST BE STOPPED. Executing a zero turn while the tractor is moving can significantly reduce your control of the tractor and will cause severe turf defacement to occur.

•Stop the forward or reverse motion of the tractor by moving the two drive control levers to neutral.

•To turn clockwise, slowly move the left control lever forward while simultaneously moving the right control lever rearward. See Figure 18.

CLOCKWISE ZERO TURN

Figure 18

•To turn counterclockwise, slowly move the right control lever forward while simultaneously moving the left control lever rearward. See Figure 19.

COUNTERCLOCKWISE ZERO TURN

Figure 19

STOPPING THE TRACTOR

•Move both drive control levers to the neutral position to stop the motion of the tractor.

•Push the PTO switch downward to the disengaged position.

•Use the deck lift handle to raise the deck to its highest position.

•If dismounting the tractor:

-Move the drive control handles fully outward in the neutral position.

-Engage the parking brake.

-Move the throttle control lever between the half and full throttle positions,

-Turn the ignition switch to “OFF’” and remove the key from the switch.

DRIVING ON SLOPES

Refer to the SLOPE GAUGE on page 10 to help determine slopes where you may not operate safely.

WARNING: Do not operate on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). The tractor could overturn and cause serious injury.

•Always drive across slopes, never up and down. Control the speed and direction of the tractor using primarily the control lever on the downhill side of the tractor, with the uphill control lever remaining essentially in a fixed position.

•Avoid turning downhill if possible. Start at the bottom of a slope and work upward. Always slow down before turning.

•Use extra care and go slowly when turning downhill.

OPERATING THE PTO

Operate the PTO clutch as follows:

•Move the throttle control lever to approximately the mid throttle position.

•Pull the PTO switch upward to the “ENGAGED” position.

•Advance the throttle lever to the operating speed (full engine speed).

•The operator must remain in the tractor seat at all times. If the operator should leave the seat without turning off the power take-off switch, the tractor’s engine will shut off.

•The PTO clutch cannot be operated when the tractor is driving in the reverse direction. The PTO will disengage when both drive control levers are moved to the reverse position, and will re-engage when one (or both) control levers are moved to the neutral or forward position.

20

Page 19 Page 21
Page 20
Image 20
Troy-Bilt RZT 50 manual Executing a Zero Turn, Stopping the Tractor, Driving on Slopes, Operating the PTO
Page 19 Page 21

RZT 50 specifications

The Troy-Bilt RZT 50 is a notable addition to the riding mower market, designed to provide both power and precision for homeowners seeking a reliable solution for lawn care. With a cutting width of 50 inches, this zero-turn riding mower allows users to tackle larger areas efficiently, making it suitable for properties with expansive lawns.

One of the standout features of the RZT 50 is its robust engine, typically powered by a 25 HP Briggs & Stratton engine. This engine delivers impressive torque and reliability, offering users the ability to handle tough mowing conditions without losing power. The mower's design prioritizes ease of use, with a trusty electric start that eliminates the hassle of manual cranking.

The RZT 50 is equipped with a dual hydrostatic drive system, which provides seamless steering and allows for easy maneuverability around obstacles such as trees, flower beds, and garden features. The zero-turn capability means that users can make tight turns without leaving uncut grass, giving the mower an edge in terms of efficiency and precision.

Another significant characteristic of the Troy-Bilt RZT 50 is its Comfort Seat, designed with ergonomics in mind. This padded, high-back seat offers support during longer mowing sessions, ensuring a comfortable riding experience. Additionally, the mower features adjustable cutting heights ranging from 1.5 inches to 4 inches, allowing users to customize their lawn care according to individual preferences and seasonal needs.

In terms of maintenance, the RZT 50 comes with a maintenance-free battery and easily accessible components for routine checks, reducing the downtime often associated with mower upkeep. Moreover, the mower boasts a durable steel frame and deck, ensuring longevity and resistance to wear over time.

Overall, the Troy-Bilt RZT 50 stands out with its combination of power, innovation, and user-friendly features, making it an ideal choice for homeowners aiming to maintain a lush and well-manicured lawn with minimal effort. With its thoughtfully designed capabilities, the RZT 50 proves that effective lawn care can be both easy and enjoyable.
Top Page Image Contents