8.Using care to prevent the front hanger rod from falling back into the deck bracket slots, carefully slide the cutting deck (from the right side) out from underneath the tractor.

DECK INSTALLATION

To install the mower deck, proceed as follows:

1.While holding up the deck front hanger rod, carefully slide the deck underneath the right side of the tractor.

2.While still holding the front hanger rod, slide the deck forward until the front hanger rod can be lowered into the slots at the front of the deck.

3.Lower the front hanger rod into the slots of the front deck bracket, then slide the deck rearward.

4.Maneuver the deck so that the slots in the two rear deck hanger brackets approximately align with the deck lift arms of the tractor. Refer to Figure 30.

5.Use the tractor deck lift handle to lower the deck lift arms into the slots of the rear deck hanger brackets.

6.Pull the deck support pins outward and maneuver the deck as necessary to align the holes in the deck lift arm with the pins. Refer to Figure 30.

7.When aligned, push each pin fully inward through the lift arms to secure the arms in the rear hanger bracket slots.

8.Make certain the ‘V’ belt is in the spindle pulleys on the deck, then route the belt rearward beneath the tractor frame and above the two transmission tubes

9.Install the ‘V’ belt onto the PTO pulley using one of the following two methods.

WARNING: The muffler at the rear of the tractor may be extremely hot, and could cause serious burns. Use extreme caution when near the muffler. Allow the muffler to fully cool before installing the belt.

Using the idler pulley to tension the belt.

•Using the deck lift handle, raise the deck to the position that provides the most horizontal run of the belt between the deck idler pulleys and the PTO pulley on the bottom of the engine.

•Install the belt in the PTO pulley on the bottom of the engine.

•Route the backside of the belt around the fixed idler pulley of the deck. Refer to Figure 29.

•Working from the middle of the tractor, pivot the idler bracket/movable pulley rearward against the spring tension and slide the backside of the belt onto the movable idler pulley. Refer to Figure 29.

Rolling the belt into the PTO pulley.

•Using the deck lift handle, raise the deck to the position that provides the most horizontal run of the belt between the deck idler pulleys and the PTO pulley on the bottom of the engine.

•Make certain the belt is in the spindle pulleys of the deck, and that the backside of the belt is against both the fixed and movable idler pulleys. Refer to Figure 29.

•Sitting behind the tractor, facing forward, make certain the belt is not twisted; then reach beneath the tractor to grasp the belt and pull it toward the PTO pulley.

WARNING: Use caution to prevent pinching your fingers when rolling the belt onto the PTO pulley.

•Pull the right side of the belt rearward and place the narrow V side of the belt into the PTO pul- ley. See Figure 31.

•While holding the belt and pulley together, rotate the pulley to the left (See Figure 31). Continue holding and rotating the pulley and belt until the belt is fully rolled into the PTO pulley.

PTO Pulley

PTO Belt

Rotate

Pulley

Transmission

Tube

Figure 31

29

Page 28 Page 30
Page 29
Image 29
Troy-Bilt RZT 50 manual Deck Installation, Using the idler pulley to tension the belt, Rolling the belt into the PTO pulley
Page 28 Page 30

RZT 50 specifications

The Troy-Bilt RZT 50 is a notable addition to the riding mower market, designed to provide both power and precision for homeowners seeking a reliable solution for lawn care. With a cutting width of 50 inches, this zero-turn riding mower allows users to tackle larger areas efficiently, making it suitable for properties with expansive lawns.

One of the standout features of the RZT 50 is its robust engine, typically powered by a 25 HP Briggs & Stratton engine. This engine delivers impressive torque and reliability, offering users the ability to handle tough mowing conditions without losing power. The mower's design prioritizes ease of use, with a trusty electric start that eliminates the hassle of manual cranking.

The RZT 50 is equipped with a dual hydrostatic drive system, which provides seamless steering and allows for easy maneuverability around obstacles such as trees, flower beds, and garden features. The zero-turn capability means that users can make tight turns without leaving uncut grass, giving the mower an edge in terms of efficiency and precision.

Another significant characteristic of the Troy-Bilt RZT 50 is its Comfort Seat, designed with ergonomics in mind. This padded, high-back seat offers support during longer mowing sessions, ensuring a comfortable riding experience. Additionally, the mower features adjustable cutting heights ranging from 1.5 inches to 4 inches, allowing users to customize their lawn care according to individual preferences and seasonal needs.

In terms of maintenance, the RZT 50 comes with a maintenance-free battery and easily accessible components for routine checks, reducing the downtime often associated with mower upkeep. Moreover, the mower boasts a durable steel frame and deck, ensuring longevity and resistance to wear over time.

Overall, the Troy-Bilt RZT 50 stands out with its combination of power, innovation, and user-friendly features, making it an ideal choice for homeowners aiming to maintain a lush and well-manicured lawn with minimal effort. With its thoughtfully designed capabilities, the RZT 50 proves that effective lawn care can be both easy and enjoyable.
Top Page Image Contents