Manuals / True Manufacturing Company / Kitchen Appliance / Refrigerator

True Manufacturing Company TCGDZ-50 Light Bulb Replacement, Shelf Mounted Bulb Replacement

Models: TCGDZ-50

1 21

Download 21 pages 58.67 Kb

Page 15

LIGHT BULB REPLACEMENT

True Food Service Equipment, Inc.

MAINTENANCE, CARE & CLEANING

LIGHT BULB REPLACEMENT

SHELF MOUNTED BULB REPLACEMENT:

WARNING

When replacing a light bulb make sure power to the unit is either turned off or unplugged.

A.Unplug the light assembly from the receptacle on the interior side wall. Remove shelf and light assembly from cabinet.

B.Remove the lampshield by gently squeezing the sides together and rotating out (image 1).

C.Remove bulb from the corded end of assembly by holding the bulb and gently pulling up on spring loaded lampholder which will allow enough clearance to remove bulb (image 2).

NOTE

All spring loaded lampholders are located on the left side of the cabinet as you face the front.

NOTE

Please be aware of your local ordinances for dis- posal of old florescent bulbs. These bulbs should be disposed of in a safe and proper manner.

D.Install new bulb using spring loaded lamp- holder.

E.Reinstall light assembly and shelf. Plug cord into side wall receptacle.

INTERIOR TOP BULB REPLACEMENT:

WARNING

When replacing a light bulb make sure power to the unit is either turned off or unplugged.

A. Remove the lampshield by gently squeezing

the sides together and rotating out (image 3).

B. Remove bulb by gently pushing bulb back into

spring loaded lampholder which will allow

enough clearance to remove bulb (image 4).

C. Install new bulb using spring loaded lamp-

holder.

D. Reinstall light lampshield by sliding rear "U"

channel of lampshield over metal bracket and

gently squeezing lampshield to fit front "U"

channel over front metal bracket (images 5-6).

➟

1

Squeeze lampshield and rotate out.

➟

3

Squeeze lampshield and rotate out.

➟

5

Squeeze lampshield "U" channel into position over metal bracket.

7

➟

2

Remove bulb by gently pulling up on spring loaded lampholder.

➟

4

Remove bulb by gently pushing bulb into spring loaded lamp- holder.

6

lampshield "U" channel in position over metal bracket.

E. Image 7 shows assembly properly installed.

Interior top light assembly properly installed.

13

www.truemfg.com

13

Image 15

True Manufacturing Company TCGDZ-50 Light Bulb Replacement, Shelf Mounted Bulb Replacement, Interior Top Bulb Replacement

Contents

INSTALLATION MANUAL FOR TRUE FOOD SERVICE EQUIPMENT, INCTCGDZ-50 TABLE OF CONTENTSLoss Or Spoilage Of Products In Your By Warranty. In Addition To FollowingRecommended Installation Procedures NOTICE TO CUSTOMERSAFETY PRECAUTIONS True Food Service Equipment, Inc SAFETY INFORMATIONmaintained, will give you many years of trouble-free service Refrigerant Disposal PROPER DISPOSAL OF THE DISPLAY CASEUSE OF EXTENSION CORDS Before You Throw Away Your Old Display Case Take off the doorsFor models with standard power cord HOW TO CONNECT ELECTRICITYHard wiring is required on specific Display Cases For personal safety, this appliance must be properly groundedOWNERSHIP INSTALLATION / OPERATION INSTRUCTIONSTrue Food Service Equipment, Inc INSTALLATION / OPERATION INSTRUCTIONSTOOLS REQUIRED Warranty is void if ventilation is insufficientLOCATING LEVELINGINSTALLATION / OPERATION INSTRUCTIONS Power supply cord ground should not be removedELECTRICAL INSTRUCTIONS True Food Service Equipment, IncINSTALLATION / OPERATION INSTRUCTIONS Wire Gauge for 2% Voltage Drop in Supply CircuitsCONDUCTORS AND CIRCUITS True Food Service Equipment, IncTrue Food Service Equipment, Inc REPLACEMENT PARTSSTARTUP RECOMMENDATIONattached caps are plugged into SHELVING INSTALLATION REFRIGERATED BAKERYSHELF INSTALLATION for lights to work. If less thanTrue Food Service Equipment, Inc OPTIONAL INSTALLING OPTIONAL CASTORSCASTOR INSTALLATION TOOLS REQUIRED Castors not available for hard wired or remote modelsTrue Food Service Equipment, Inc OPTIONAL INSTALLING OPTIONAL FORMICA KITFORMICA KIT INSTALLATION FORMICA KIT COMPONENTS Refer to image 1 for placement of Formica panelsCABINET CLEANING True Food Service Equipment, Inc MAINTENANCE, CARE & CLEANINGOPTIONAL SEALING CABINET TO FLOOR True Food Service Equipment, Inc MAINTENANCE, CARE & CLEANING LIGHT BULB REPLACEMENTSHELF MOUNTED BULB REPLACEMENT INTERIOR TOP BULB REPLACEMENTcontroller functions closer to sea level TEMPERATURE CONTROL ADJUSTMENT FOR HIGH ALTITUDE ONLYDANFOSS TEMPERATURE CONTROL TERMSCLEANING THE CONDENSER COIL CONDENSER CLEANING TOOLS REQUIREDTrue Food Service Equipment, Inc MAINTENANCE, CARE & CLEANING True Food Service Equipment, Inc MAINTENANCE, CARE & CLEANING 6. Reconnect the electrical power to the unit2. Remove the louvered grill IMPORTANT WARRANTY INFORMATIONTrue Food Service Equipment, Inc MAINTENANCE, CARE & CLEANING STAINLESS STEEL EQUIPMENT CARE AND CLEANINGrecommended on plastic parts. Warm soap and water will suffice True Food Service Equipment, Inc MAINTENANCE, CARE & CLEANINGSTAINLESS STEEL EQUIPMENT CARE AND CLEANING The use of stainless steel cleaners or other such solvents is not404A/134A COMPRESSOR WARRANTY WARRANTY INFORMATION U.S.A. and Canada ONLY! U.S.ATrue Food Service Equipment, Inc ADDITIONAL FOUR YEAR COMPRESSOR WARRANTY