Manuals / Turbosound / Home Audio / Speaker

Turbosound TA-500DP, TA-500TDP Attaching the Tilt Straps, Biscuit slides into lower cabinet

Models: TA-500HM TA-500DP TA-500 TA-500H TA-500HDP TA-500T TA-500TDP

1 73

Download 73 pages 47.45 Kb

Page 33

user manual

TA-500

Figure 9: Biscuit slides into lower cabinet

Attaching the Tilt Straps

When all cabinets have been linked and the top chains attached, the tilt straps can now be attached.

First attach the longer strap to the flybar by sliding the flat buckle into the tilt strap attachment point. Slide the flat buckle on the shorter strap into the tilt strap point on the bottom of the cabinet, insert the free end of the strap through the centre of the ratchet spindle, and pull to apply some tension before ratcheting the column.

WARNING

The tilt strap is designed to ratchet in both directions, an improvement over previous versions which did not allow incremental tilt reduction. However, at all times please note that if the tension on the strap is released suddenly, the column of enclosures may tend to swing violently forwards and care must be taken to avoid danger to persons in the vicinity. It is essential to check that nobody is standing immediately in front of the column, and to give a suitable warning, before the strap is released. Ideally, two persons should support the row from the side whilst the strap is released, or alternatively the bottom row may be returned to the ground before release. In any event it is essential that all personnel in the vicinity are aware that the system is about to move and that they must keep clear.

SAFETY NOTE: Turbosound flying systems have been designed and constructed to a high standard of safety and tested to the most demanding of specifications with a high safety factor. However, anyone involved in flying

ANY sound system, especially in a touring capacity, should take note of the following advice: The rigging of a flown sound system may be dangerous unless undertaken by qualified personnel with the required experience to perform the necessary tasks. Fixing of hanging points in a roof should always be carried out by a professional rigger and in accordance with the local rules of the venue. The house rigger and/or building manager must always be consulted.

TA-500 user manual

Page 33

Image 33

Turbosound TA-500DP, TA-500TDP, TA-500HDP, TA-500HM user manual Attaching the Tilt Straps, Biscuit slides into lower cabinet

Contents

Aspect TA-500 Systems TA-500 TA-500 TA-500 Audio Connections & Controls TA-500HDP EC Declaration of Conformity Turbosound Aspect System Concepts Introduction Aspect Polyhorn Concept TA-880 TA-500 Narrow 25º horizontal coverage Loudspeaker Management System LMS Concept LMS-D2X Loudspeaker Management SystemsNetwork Capability Self-powered Loudspeakers Power AmplifiersDigital Controllers Aspect Loudspeaker Components TA-500 TA-500tDP Self-powered Touring Three-way Loudspeaker TA-500DP Self-powered Three-way LoudspeakerTA-500 Three-way Loudspeaker TA-500t Touring Three-way Loudspeaker TA-500H Horizontal Three-way Loudspeaker TA-500HDP Self-powered Horizontal Three-way LoudspeakerTA-500HM Two-way High/Mid Loudspeaker TSW-218 Subwoofer B18 Subwoofer B18DP Self-powered Subwoofer Transportation Overview Flying and Stacking Safety Notes on Rigging Secondary Safeties Safety Inspections TA-500 Sample Certificate of Load Test Aspect TA-500 Flying Systems Flying HardwareHorizontal Coverage Vertical Coverage Flybar Settings TA-500T Touring Flying SystemTouring two-wide flybar TOP View FC-500T Flying Chains Flying Matrix TA-500 Integral Flying Hardware TS-890 Tilting Straps Captive Biscuit Bolt Locking Mechanism Connecting Flying Chains to the Cabinet Sliding the top chain profile into the slot Assembly of the Top Chains to the Cabinet Adding additional rows Connection of additional rows Attaching the biscuit Setting the angles between rows Biscuit slides into lower cabinet Attaching the Tilt Straps Front view of the assembled cluster Lifting the column TA-500 TA-500 Install Flying System Rigging Instructions TA-500 TA-500 Array is now ready to pick up Flying a single TA-500 cabinet using M10 eyebolts LMS Series Loudspeaker Management Systems Mechanical InstallationIntroduction Unpacking LMS-D24 and D26 Loudspeaker Management Systems Features LCD Front Panel Functions TA-500 Rear Panel Functions Selecting a Factory Preset Operating the LMS-D24 and D26 Starting upCreating a Crossover Navigation and Viewing Parameters EQ1 100Hz 0dB Navigation Out1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dB Preset Recall Presets Store My System Preset Store DSP Processing Layout Input DSP block diagram Output DSP block diagramStereo / Mono Formats DSP processing Input Channels A Delay 1.50ms A Freq Shape Parametric Equalisation High and Low shelving filtersParametric filters Output Channels Gain and Polarity Delay High and Low Pass Filters Out1 Freq Shape LPF 2.50k LR24 Out1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Routing Limiters Utilities Utility functions General Features & Facilities T-45 High Efficiency Audio Power Amplifiers Front Panel Functions T-25 Front Panel Functions T-45 Mains Power Powering UpSafety Earthing Voltage Setting Voltage RangeAudio Connections & Controls Gain and Sensitivity Settings PolarityInput Impedance Attenuation & Gain Setting Output ConnectionsDamping Factor Cooling System Long Speaker Lines TA-500 TA-500t TA-500H TA-500HM Appendix a Technical Specifications TA-500DP TA-500tDP TA-500HDP Stock Code Model Description Appendix B Spare Parts List Appendix C Warranty TA-500