Manuals / Turbosound / Home Audio / Speaker

Turbosound TA-500TDP, TA-500HDP Polarity, Input Impedance, Gain and Sensitivity Settings

Models: TA-500HM TA-500DP TA-500 TA-500H TA-500HDP TA-500T TA-500TDP

1 73

Download 73 pages 47.45 Kb

Page 66

Polarity

user manual

TA-500

of performance may be experienced if connected to unbalanced sources. If it is unavoidable, however, the following wiring convention should be used.

Pin 1	Screen - connect to chassis of the unbalanced equipment,
	or left disconnected at the unbalanced end
Pin 2	signal hot
Pin 3	Signal cold

Polarity

In accordance with international standards, T series amplifiers are supplied with Pin 2 hot (+), so a positive (+V) input gives a positive (+V) output from the positive (+) output terminals.

Input Impedance

Each amplifier channel has an input impedance of 10kΩ, seen between pins 2 & 3 of the XLR.

When used with the LMS-D6 Loudspeaker Management System, distribution amplifiers are not required when a large number of T-25 or T-45 amplifier inputs are driven in parallel.

Gain and Sensitivity Settings

Gain settings are changed internally by simple jumper links. Two rows of pins marked - GAIN A and GAIN B - are situated on the input PCB (PCB701). A jumper link sets the gain and the settings are as follows:

Link 1 & 2	Gives 32dB gain
Link 3 & 4	Gives 26dB gain
Link 2 & 3	Gives approx 37.5dB gain

NOTE: Factory setting is normally link 1 & 2 = 32dB gain.

TA-500 user manual

Page 66

Image 66

Turbosound TA-500TDP, TA-500HDP, TA-500DP, TA-500HM user manual Polarity, Input Impedance, Gain and Sensitivity Settings

Contents

Tel +44 01403 711447 Fax +44 Star Road, Partridge GreenWest Sussex RH13 8RY United Kingdom ASPECT TA-500SYSTEMS TA-500 TA-500DP TA-500tTA-500 TA-500 Features TA-500Attenuation & Gain Setting TA-500Audio Connections & Controls EC DECLARATION OF CONFORMITY TA-500INTRODUCTION Turbosound Aspect System ConceptsTA-500 The Aspect Polyhorn Concept TA-500narrow 25º horizontal coverage TA-880TA-500 TA-500Network Capability The Loudspeaker Management System LMS ConceptLMS-D2XLoudspeaker Management Systems TA-500Digital Controllers Power AmplifiersSelf-poweredLoudspeakers Aspect Loudspeaker ComponentsNeodymium magnets are used throughout all drive units. This results in higher efficiency, less power compression and reduced overall weight TA-500TA-500tTouring Three-wayLoudspeaker TA-500DP Self-powered Three-wayLoudspeakerTA-500 Three-wayLoudspeaker TA-500Loudspeaker TA-500HDP Self-poweredHorizontal Three-wayTA-500HHorizontal Three-wayLoudspeaker TA-500HM Two-wayHigh/Mid LoudspeakerB18DP Self-poweredSubwoofer B18 SubwooferTA-500 Transportation TA-500FLYING AND STACKING OverviewTA-500 Safety Notes on Rigging TA-500Safety Inspections Secondary SafetiesTA-500 The Health and Safety at Work Act TA-500Sample Certificate of Load Test TA-500Horizontal Coverage FLYING HARDWAREAspect TA-500Flying Systems Vertical CoverageTouring two-wideflybar Flybar SettingsA. TA-500TTOURING FLYING SYSTEM TA-500BOTTOM VIEW Figure 2 Flybar Lifting Points and DimensionsTOP VIEW Figure 1 FB-500T/2WTouring Two-wideFlybarTable 1 Flying Matrix FC-500TFlying ChainsTA-500 Net weight is 0.5kg 1.1lbs FC-500TLong Flying Chain Net weight is 1kg 2.2lbsNet weight is 1kg 2.2lbs Inter-cabinetLink FC-500TStandard Length Flying ChainTS-890Tilting Straps 0.5m4.5m Integral Flying HardwareBolt BoltCaptive biscuit Captive BiscuitFigure 4 Locking Mechanism Connecting Flying Chains to the CabinetBolt Slot TA-500Sliding the top chain profile into the slot TA-500Connection of additional rows Figure 6 Adding additional rowsTA-500 Attaching the biscuit Setting the angles between rowsFigure 8 Index link angle setting TA-500Attaching the Tilt Straps Figure 9 Biscuit slides into lower cabinetTA-500 Figure 11 Rear view of the assembled cluster Lifting the columnFigure 10 Front view of the assembled cluster TA-500TA-500 B. TA-500INSTALL FLYING SYSTEM TA-500Rigging Instructions TA-500STEP 2 - Fit a 3-widehinge brace to the top of the array and a 3-widerear brace to the bottom of the array using the twelve M10 x 40mm hex screws provided and torque to 25Nm. The use of thread-lockingcompound is recommended see Appendix. Fit an M10 eyebolt to the centre of the rear brace TA-500Locate the four M10 x 40mm hex screws from the fixings kit and insert these through the enclosure connector into the rigging points on the two outside cabinets, together with four M10 shakeproof washers TA-500TA-500 STEP 4 - The array is now ready to pick upFlying a single TA-500cabinet using M10 eyebolts TA-500Introduction Mechanical InstallationLMS SERIES LOUDSPEAKER MANAGEMENT SYSTEMS UnpackingFeatures LMS-D24AND D26 LOUDSPEAKER MANAGEMENT SYSTEMSTA-500 Front Panel Functions TA-500Text display - preset, channel, parameter and status information is shown on the 2x 24- character text display. In most screens the currently selected channel is displayed on the upper line and the edit parameter on the lower line. To simplify the display and enhance security, some parameters or parameter pages are omitted when not relevant TA-500TA-500 Rear Panel FunctionsPower Inlet Network CardCreating a Crossover Selecting a Factory PresetOperating the LMS-D24and D26 Starting up TA-500Gain In A FreqWidth EQ1 100HzOut1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dB NavigationTA-500 LMS-D26LMS-D26 PresetsPreset Recall Preset NameTA-500 Preset StorePreset NameStereo / Mono Formats DSP Processing Layout Input DSP block diagramOutput DSP block diagram TA-500LMS-D26 In A Delay 1.50msIn A Gain 0.0dB DSP processing Input ChannelsHPF 20.0Hz In A FreqShape LR24EQ1 100Hz SlopeGain 12dBOut1 Gain Pol 0.0dB Rev Out1 Delay 1.50msDelay Output Channels Gain and PolarityTA-500 Out1 Freq Shape LPF 2.50k LR24High and Low Pass Filters LMS-D26TA-500 Out1 Freq Slope Gain EQ - 100Hz 12dB 0.0dBOut1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dB LMS-D26Limiters Out1 Thresh LIM 4.0dBOut1 Source Inp A RoutingTA-500 Util Screen ParaEQ 100% BW=QUtilities Utility functions LMS-D26General Features & Facilities TA-500Front Panel Functions T-25 TA-500Ch. ACh.B Front Panel Functions T-45 TA-500Safety Earthing Mains PowerPowering Up Mechanical InstallationAudio Connections & Controls Voltage SettingVoltage Range TA-500Input Impedance Gain and Sensitivity SettingsPolarity TA-500Damping Factor Attenuation & Gain SettingOutput Connections TA-500Long Speaker Lines The Cooling SystemTA-500 TA-500 APPENDIX A TECHNICAL SPECIFICATIONSTA-500 TA-500tTA-500tDP TA-500TA-500DP TA-500HDPStock Code APPENDIX B SPARE PARTS LISTTA-500 ModelAPPENDIX C WARRANTY TA-500Turbosound Limited Star Road Partridge Green TA-500West Sussex RH13 8RY United Kingdom