2.Wait until the display says Registration Complete (about 30 seconds), then pick up the handset; press home/flash.
3.If you don’t hear a dial tone or the display says Registration Failed, charge the battery completely, then try again.
Adapter and Battery Information
AC adapter | Base | Charger | |
Part number | |||
Input voltage | 120V AC, 60 Hz |
| |
| 6V DC @ |
| |
Output voltage | 500mA | 8V AC @ | |
7V DC @ | 300mA | ||
| |||
| 800mA (USB) |
|
xx Use only the supplied AC adapters.
xx Use the proper adapter for the base & any chargers.
xx Do not place the unit in direct sunlight or subject it to high temperatures.♦
♦
Battery pack (with normal use)
Part number | ||
Capacity | 300mA, 2.4V DC | |
400mA, 2.4V DC | ||
| ||
Talk time | about 7 hours | |
Standby time | about 7 days | |
Battery life | about 1 year |
xx Replace the battery when the talk or standby time becomes noticeably reduced. For replacements, call the Parts Department (see the front cover).
xx When the battery gets low, the handset beeps and shows a low battery alert; put the handset in the cradle for recharging.
Rechargeable Battery Warning
xx This equipment contains a rechargeable Nickel-
xx Nickel is a chemical known to the state of Califor- nia to cause cancer.
xx Do not
xx The batteries in this equipment may explode if disposed of in a fire.
xx Do not charge the batteries in any charger other than the one specified in the owner's manual. Using another charger may damage the battery or cause it to explode.
xx As part of our commitment to protecting our environment and conserving natural resources, Uniden voluntarily participates in an RBRC® industry program to collect and recycle used
your area. (RBRC® is a ♦ registered trademark of the ♦ Rechargeable Battery ♦ Recycling Corporation.)
Rechargeable batteries must be recycled or disposed of properly.
Warning! The cords on this product and/or accessories contain lead, a chemical known to the state of California to cause birth defects or other reproductive harm. Wash hands after handling.
Uniden works to reduce lead content in our products & accessories.
Compliance Information
FCC Part 68 Information
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the phone company.
An applicable Universal Service Order Codes (USOC) certification for the jacks used in this equipment is provided (i.e., RJ11C) in the packaging with each piece of approved terminal equipment. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a phone line. Excessive RENs on a phone line may result in devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the telephone provider. The REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by
##are the REN without a decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the
26 - English
