TROUBLE SHOOTING AND PROBLEM SOLVING

1. Problem:

Smoke puffs from furnace

Solution:

A.Check chimney draft. Check for blocked chimney or flue pipe. Use mirror to check chimney clearance.

B.Check ash pit — if it is too full, empty.

C.Make sure furnace room is not too airtight.

D.Make sure all of chimney mortar connections are airtight.

E.Check ash drawer. Make sure it's airtight.

F.Check chimney for possible down-draft caused by taller surrounding trees or objects. Correct with proper chimney vent cap.

G.Check the possibility of a cold chimney forcing cool gases backward. Remedied by properly insulating chimney with non-combustible liner — non-combustible insulation.

H.Fuel may be too green.

I.Make sure no other fuel burning devices are connected to the chimney impairing the draft.

J.Check chimney draft, it should be .06 inches of water column.

2. Problem:

Inadequate heat being delivered to your home

Solution:

A.Check home insulation — is it adequate?

B.Check hook-up to furnace — is it installed correctly?

C.Cool air inlet may be inadequate or furnace room too airtight.

D.Your wood fuel may be too low grade. Hardwoods are recommended.

E.Make sure your hot air duct (and other duct work) is airtight.

F.If furnace room is warm but your home isn't, check back draft dampers.

G.Is air to the blower available?

3. Problem:

Excess smoke or flames coming out door when refueling

Solution:

A.Wait 15 seconds and open door SLOWLY — then refuel.

B.Check length of flue pipe to chimney. Your unit should be within six (6) feet of your chimney.

C.Make sure chimney cap is not too close to the top of the chimney.

D.Check chimney draft — make sure chimney flue pipe is clean and chimney is of adequate height.

E.Make sure you're not suffocating the fire with excessive amounts of unburned wood.

F.Slide baffle should be pulled out prior to load door opening.

4.Problem:

Distribution blower vibrating

Solution:

A.Tighten blower wheel to motor shaft.

B.Check for bad fan bearings.

5.Problem:

Distribution blower continues to run or will not run

Solution:

A.Check fan limit or heat sensor and cable.

B.Check to see that blower is properly wired. (See Wiring and Assembly Instructions).

C.Check fuse box or power source.

D.Check power supply.

6.Problem:

Draft blower continues to run or will not run

Solution:

A.Check wiring.

B.Check thermostat or thermostat wire for short.

C.Make sure temperature is calling for heat.

7.Problem:

Odor from first fire

Solution:

A.The odor from new steel should disappear in a few hours.

B.If the odor remains, call you dealer immediately. A bad weld can cause a fume leak.

8.Problem:

Excessive Creosote

Solution:

A.Check the grade of wood you are burning.

B.Make sure your unit is serviced by its own proper chimney.

C.Check length of flue pipe and its connections.

D.Make sure you are burning the smallest, hottest fire to adequately heat your home.

E.Also see Solutions to Problem one.

13

Page 14 Page 16
Page 15
Image 15
United States Stove 1600, 1800 manual Trouble Shooting and Problem Solving, Solution
Page 14 Page 16

1600, 1800 specifications

The United States Stove Company is known for producing high-quality, efficient wood and coal stoves made for both residential and commercial applications. Among their notable models are the 1600 and 1800 series, both of which provide reliable heating solutions with a blend of traditional craftsmanship and modern technology.

The United States Stove 1600 model is designed for versatility, making it ideal for a variety of spaces, including homes, cabins, and workshops. It features a sturdy cast iron construction, contributing to its durability and ability to retain heat effectively. The 1600 is equipped with a large firebox that accommodates larger logs, allowing for extended burn times and less frequent loading. One of its main features is an air wash system that helps keep the glass door clean, providing a clear view of the fire while enhancing the stove's efficiency.

On the other hand, the United States Stove 1800 model typically offers a larger heating capacity compared to the 1600, making it suitable for bigger rooms or open floor plans. This model also boasts a robust design, often made from heavy-duty steel, which not only enhances its longevity but also provides excellent heat retention. The 1800 series may come with advanced features such as a secondary combustion system, promoting cleaner burning and improved efficiency by maximizing heat output while reducing smoke emissions.

Both models feature easy-to-use mechanical controls for regulating airflow, allowing users to adjust the fire's intensity according to their heating needs. Additionally, they are designed to be compatible with various flue venting systems, providing flexibility in installation options.

Safety is a paramount concern in both the 1600 and 1800 models, with built-in safeguards such as a thermal protective barrier and an external ash door for easy cleaning and maintenance.

Overall, the United States Stove 1600 and 1800 models embody a commitment to quality craftsmanship, efficiency, and user-friendly designs, making them excellent choices for anyone in search of reliable heating solutions in their living or working spaces. With their combination of traditional design elements and modern combustion technologies, these stoves stand out in the competitive market of heating appliances.
Top Page Image Contents