OWNER’S MANUAL
OPERATING
FIREPLACE
Continued
OPTIONAL REMOTE
OPERATION
Note: All remote control accessories must be purchased separately (See Accessories on page 27). Follow instructions included with the remote control.
Thermostat Control Operation
Selector Switch in Remote
Position (GHRC Optional
Remote Control)Control Knob in
On Position
| LO H |
| ON |
| I |
|
|
REMOTE OFF ON |
| T |
|
| L |
| |
|
| O | OFF |
|
| I | |
|
| P |
|
Flame Adjustment Knob
Figure 46 - Setting the (GHRC) Remote Control Selector Switch, Valve Control Knob, and Flame Adjustment Knob for Remote Operation
•In auto mode, the room tempera- ture is controlled by the thermo- stat in the
IMPORTANT: This remote control has been specially engineered to take an air temperature sample every 5.5 minutes in auto mode. It will not re- spond immediately to the tempera-
(Optional GHRCT Only) The thermostat control setting on the remote control unit can be set to any comfort level between HI and LO. The burners will turn on and off automatically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of
Selector Switch in
Remote Position
(GHRCT Optional
Remote Control)
ON
OFF
REMOTE
Control Knob in On Position
O | H |
|
|
L |
| ON | |
| I |
|
|
|
| T |
|
|
| O | OFF |
|
| L |
|
|
| I |
|
|
| P |
|
ture setting being turned up or down.
IMPORTANT: The
the central heating system, etc.
NOTICE: You must light the pilot before using the
1. After lighting, let pilot flame burn for |
about one minute. Turn control knob |
on the control valve to ON position. |
Turn flame adjustment knob any- |
where between HI and LO. Slide the |
selector switch to the REMOTE posi- |
tion. Note: The burners may light if |
when selector switch was last turned |
off. You can now turn the burners on |
and off with either optional |
remote control unit. |
Flame Adjustment Knob
Figure 47 - Setting the (GHRCT) Selector Switch, control Knob, and Flame Adjustment Knob for Remote Operation
GHRC Series Operation:
2a. Press the ON/OFF button to turn the burners on and off. When turning burners off, the pilot will remain lit.
GHRCT Series Operation:
2b. Select the MAN (manual) or AUTO button on the
•In manual mode, turn burners on or off by pressing the ON or OFF buttons on the
3.Use the STATUS button on the hand- held remote control unit to see the operation mode being used and the temperature setting selected. A red light will come on beside the opera- tion mode being used.
4.To turn the burners off when operat- ing in the manual mode, press the OFF button. If operating in the auto mode, press the MAN button, then press the OFF button. The pilot will remain lit. IMPORTANT: To turn the pilot off, manually turn the control knob on the heater to the OFF position.
IMPORTANT: Do not leave the se- |
lector switch in the REMOTE posi- |
tion when the pilot is not lit. This will |
drain the battery. |
IMPORTANT: Be sure to press the |
ON/OFF buttons on the |
remote control unit for up to 3 sec- |
onds to assure proper operation. |
Shows Temperature Setting
Allows Burners to be Turned On and Off with the
The Heater will Automatically Cycle Between Pilot and the Heat Setting that has been Selected
HI
TEMP
MAN LO ON
AUTO OFF
STATUS
Increases Room Temperature
Decreases Room Temperature
Turns Burners On and Off
Shows Current Operation Mode
Figure 48 - |
|
(GHRCT Only) | Continued |
105500 | 19 |