Dutchwest Non-Catalytic Convection Heater

Fireplace Installations -

Through the Fireplace

The Convection heater may be installed either without legs* as a fireplace insert, or with standard legs at- tached - depending on the safety regulations that apply to your situation, the height of the fireplace opening and your own preference. For either situation, the chimney connector/positive connection kit extends back from the stove, enters the fireplace cavity, and turns upward. It then passes through the fireplace damper opening and smoke chamber and connects to the chimney flue.

In such installations, a “positive connection” must be made to the chimney flue with a special kit available from your local dealer. Also, special clearance and floor protection provisions must be observed. These provi- sions are discussed in the Clearance and Floor Protec- tion sections respectively.

Wall Pass-Throughs

Whenever possible, design your installation so the con- nector does not pass through a combustible wall. If you must use a wall pass-through in your installation, check with your building inspector before you begin and con- struct it in accordance with local building codes. Also check with the chimney connector manufacturer for any specific requirements.

Accessories are available for use as wall pass- throughs. If using one of these, make sure it has been tested and listed for use as a wall pass-through.

All combustible material in the wall is cut away a suffi- cient distance from the single-wall connector to provide the required 12” (305 mm) clearance for the connector. Any material used to close up the opening must be non- combustible.

The following wall pass-through methods may be ap- proved in your area:

•Use a section of listed factory-built chimney with a nine-inch clearance to combustibles.

•Place a chimney connector pipe inside a ventilated thimble, which is then separated from combustibles by 6” (152 mm) of fiberglass insulating material.

•If the stove is installed without legs, we recommend the use of noncombustible tiles or pavers as shims to allow air flow into the convection air inlets under the stove. Make sure not to block air slots instove bottom with shims or remove fan cover.

•Place a chimney connector pipe inside a section of listed solid-insulated, factory-built chimney, with an inside diameter 2” (51 mm) larger than the chimney connector and having 1” (25 mm) or more of insula- tion and maintaining a minimum 2 inch air space between the outer wall of the chimney and combus- tibles.

12”

(305 mm)

Chimney

Connector

12”

(305 mm)

ST420

Fig. 10 Wall pass-through enclosed with noncombustible materials.

18” (450 mm)

 

Empty Space

 

All Around the

 

Chimney Con-

Sheet Metal

nector

Cover

 

 

(One side

 

only)

ST421

Fig. 11 Hollow wall pass-through.

DO NOT CONNECT THE HEATER TO ANY AIR DISTRIBUTION DUCT OR SYSTEM

In Canada: The Canadian Standards Association has established different guidelines. Figure 11 shows one method, in which all combustible material in the wall is cut away to provide the required 18” (450 mm) clear- ance for the connector. The resulting space must remain empty.

8

30002278

Page 7 Page 9
Page 8
Image 8
Vermont Casting 2478 manual Fireplace Installations Through the Fireplace, Wall Pass-Throughs
Page 7 Page 9

2478 specifications

Vermont Castings 2478 is a premium wood-burning stove that embodies quality craftsmanship and efficiency, making it a top choice for homeowners who prioritize both style and functionality. Renowned for its durability and timeless design, the 2478 model is part of the Vermont Castings line, a brand synonymous with excellence in the world of heating appliances.

One of the standout features of the 2478 is its impressive heating capacity. It can efficiently heat spaces of up to 2,100 square feet, making it suitable for large living areas or even small homes. This capability is complemented by its easy-to-use, user-friendly interface, which allows for intuitive operation and precise temperature control.

The 2478 employs advanced Catalytic Combustion technology, which optimizes fuel efficiency while significantly reducing emissions. This technology ensures that the stove burns wood cleanly and effectively, maximizing heat output and minimizing the environmental impact. The catalytic converter enhances the combustion process, providing a longer burn time and requiring less frequent refueling.

In terms of construction, the Vermont Castings 2478 features a robust cast iron body that not only contributes to its aesthetic appeal but also provides exceptional heat retention. The stove is built to last, designed to withstand high temperatures while delivering consistent warmth. The cast iron grates and firebox contribute to excellent heat distribution, creating a cozy atmosphere throughout the room.

Another notable characteristic is the large glass door that offers a beautiful view of the flames, adding a visual focal point to any space. The air wash system keeps the glass clean, allowing for an unobstructed view of the fire. A variety of finishes are available, allowing homeowners to choose a style that best fits their décor, from classic black to rich enamel colors.

The Vermont Castings 2478 is also designed with safety in mind. It includes features such as an adjustable air control system for improved combustion management and a built-in heat shield that protects surrounding areas from excessive heat.

In summary, the Vermont Castings 2478 is a highly efficient, stylish wood-burning stove that provides warmth and comfort in a reliable and environmentally responsible manner. With its combination of advanced technology, durable construction, and elegant design, the 2478 is a worthy investment for any home. Whether you're seeking to enhance your living space or reduce heating costs, this stove stands out as a classic choice in the realm of heating solutions.
Top Page Image Contents