Encore Woodburning Stove

Chimney Flue

Elbow

Flue Liner

 

Thimble Sleeve

Chimney Connector

Flue

Slip Pipe

Standard Connector

Oval to

Round Adapter

Thimble

Keep sleeve end flush with flue tile

ST243

Flue Collar

ST492

Fig. 5 Chimney connection in a freestanding masonry instal- lation.

Securing the Single-wall Connector to a

Masonry Chimney

Both freestanding masonry chimneys and fireplace masonry chimneys may be used for your installation.

Freestanding Installations

If the chimney connector must pass through a combus- tible wall to reach the chimney, follow the recommenda- tions in the Wall Pass-Through section that follows.

The opening through the chimney wall to the flue (the “breech”) must be lined with either a ceramic or metal cylinder, called the “thimble”, which is cemented securely in place. Most chimney breeches incorporate thimbles, but the fit must be snug and the joint between the thimble and the chimney wall must be cemented firmly.

A special piece called the “thimble sleeve,” slightly smaller in diameter than standard connectors and most thimbles, will facilitate the removal of the chimney connector system for inspection and cleaning. Thimble sleeves should be available from your local dealer.

To install a thimble sleeve, slide it into the breech until it is flush with the inner flue wall. Do not extend it into the actual flue passage, as this could interfere with the draft.

Fig. 6 The thimble, made of either ceramic or metal, must be cemented securely in place.

The thimble sleeve should protrude 1-2” (25-50mm) into the room. (Fig. 6) Use furnace cement and thin gasket- ing to seal the sleeve in place in the thimble. Secure the chimney connector to the outer end of the sleeve with sheet metal screws.

Without a thimble, a suitable length of chimney con- nector can be extended through the breech to the inner face of the flue liner, and cemented securely in place. Additional pieces of connector are then attached with sheet metal screws.

Fireplace Installations

The chimney connector may be connected to the chimney above the fireplace opening or through the fireplace.

Above the Fireplace

The Encore may be connected to a chimney above a fireplace opening. (Fig. 7) In such installations, the stove is positioned on the hearth in front of the fireplace and the chimney connector rises from the stove top and then angles ninety degrees back into the chimney. The chimney liner should extend to the point at which the chimney connector enters the chimney.

If the chimney connector from your installation enters the chimney above a fireplace, follow all the guidelines mentioned above for freestanding installations. In addi- tion, give special consideration to the following points:

Check the clearance between the stove and the chimney connector, and any combustible trim or the mantel. Use the necessary combination of mantel, trim, and connector heat shields to achieve the required clearances.

Check the clearance between the chimney con- nector and the ceiling. If no heat shields are used, the clearance should be at least 610 mm (24”). To find out how much this clearance may be reduced with heat shields, refer to the clearance chart on Page 12.

30003842

7

Page 7
Image 7
Vermont Casting 2550CE Securing the Single-wall Connector to a Masonry Chimney, Freestanding Installations

2550CE specifications

The Vermont Casting 2550CE is a remarkable wood-burning stove that embodies both efficiency and style, making it a preferred choice for those who desire a reliable heating solution combined with aesthetic appeal. This model stands out in the realm of traditional wood stoves, offering an exceptional blend of performance features and innovative technologies.

At the heart of the 2550CE is its robust cast iron construction, which contributes to superior heat retention and distribution. Cast iron is known for its ability to radiate warmth long after the fire has dwindled, ensuring a cozy atmosphere in your living space. This model also features a large ceramic glass door, providing a captivating view of the flames while allowing for easy monitoring of the fire's conditions.

One of the defining characteristics of the Vermont Casting 2550CE is its advanced secondary combustion system. This technology enhances the stove's efficiency by reburning the exhaust gases, thus extracting maximum heat from the wood and reducing emissions. This not only makes for a cleaner burn but also extends the burn time, allowing users to enjoy an extended period of warmth with fewer reloads.

The 2550CE is designed with functionality in mind, equipped with an easy-to-use air control system that enables precise regulation of airflow. This allows users to adjust the fire’s intensity based on their immediate heating needs, maximizing both comfort and fuel efficiency. Moreover, the stove’s large firebox accommodates logs up to 18 inches in length, making it practical for those who prefer to minimize the frequency of reloads.

In terms of style, the Vermont Casting 2550CE features a classic design that complements various interior decor styles, including rustic, traditional, and modern settings. Available in several finishes, including matte black and enamel options, the stove can be customized to match individual tastes and home aesthetics.

The commitment to sustainability is another significant aspect of the 2550CE. With its lower emissions rates complying with EPA standards, homeowners can enjoy a warm and inviting environment while being mindful of their environmental impact. Overall, the Vermont Casting 2550CE combines time-tested craftsmanship with modern technology, making it an ideal choice for anyone seeking an efficient and elegant wood-burning stove.