Vermont Casting 2550CE Double-wall Chimney Connectors, Single-wall Chimney Connectors

Encore Woodburning Stove

Flue Pipes with a spigot and socket joint should be fitted with the socket facing upwards, to contain con- densates and moisture within the flue. Joints should be made gas tight using proprietary jointing accessories, or, where appropriate, by packing joint with noncombus- tible rope and fire cement.

Double-wall connectors must be tested and listed for use with solid-fuel burning appliances. Single-wall con- nectors should be made of 24 gauge or heavier steel. Do not use galvanized connector; it cannot withstand the high temperatures that can be reached by smoke and exhaust gases, and may release toxic fumes under high heat. The connector may be 152 mm (6”) or 203 mm (8”) in diameter.

If possible, do not pass the chimney connector through a combustible wall or ceiling. If passage through a com- bustible wall is unavoidable, refer to the section on Wall Pass-Throughs. Do not pass the connector through an attic, a closet or similar concealed space. The whole connector should be exposed and accessible for in- spection and cleaning.

In horizontal runs of chimney connector, maintain a dis- tance of 610 mm (24”) from the ceiling. Keep it as short and direct as possible, with no more than two 90° turns. Slope horizontal runs of connector upward 6 mm per metere (1/4” per foot) going from the stove toward the chimney. The recommended maximum length of a hori- zontal run is 914 mm (36”), and the total length should be no longer than 2.4 m (8’). In cathedral ceiling instal- lations, extend the prefabricated chimney downward to within 2.4 m (8’) of the stove.

Wear gloves and protective eyewear when drilling, cutting or joining sections of chimney connector.

Double-wall Chimney Connectors

Information on assembling and installing double-wall connectors is provided by the manufacturer of the double-wall pipe. Follow the manufacturer’s instructions exactly as you assemble the connector and attach it to the stove and chimney. Using chimneys and connectors from the same manufacturer makes the assembly and installation straightforward.

NOTE: For installations using double-wall connectors, minimum clearances must conform to the listed clear- ances in the clearance chart on Page 14.

If the Encore is equipped with the 203 mm (8”) flue collar, an oval-to-round adapter will be needed. Double- wall oval-to-round adapters are available from some manufacturers. Your local dealer can help you select the right connector.

Single-wall Chimney Connectors

•Begin assembly at the flue collar of the stove. Insert the first crimped end into the stove’s flue collar, and keep each crimped end pointing toward the stove.

(Fig. 4) Using the holes in the flue collar as guides, drill 3 mm (1/8”) holes in the bottom of the first sec- tion of chimney connector and secure it to the flue collar with three #10 x 1/2” sheet metal screws.

•Secure each joint between sections of chimney connector, including

telescoping joints, with at least three (3) sheet metal screws. The pre-drilled

holes in the top of each section of chimney con- nector serve as guides when you drill 3 mm (1/8) holes in the bottom of the next section.

•Secure the chimney con-

nector to the chimney.	Fig. 4 the crimped end
Instructions for various	of the connector points
installations follow.	toward stove.

•Be sure the installed stove

and chimney connector are correct distances from nearby combustible materials.

NOTE: Special slip pipes and thimble sleeves that form telescoping joints between sections of chimney con- nector are available to simplify installations. They often eliminate the need to cut individual connector sections. Consult your local dealer about these special pieces.

Securing the Single-wall Connector to a

Prefabricated Chimney

Follow the installation instructions of the chimney manufacturer exactly as you install the chimney. The manufacturer of the chimney will supply the acces- sories to support the chimney, either from the roof of the house, at the ceiling of the room where the stove is installed, or from an exterior wall.

Special adapters are available from your local dealer to make the connection between the prefabricated chimney and the chimney connector. The top of such adapters attaches directly to the chimney or to the chimney’s ceiling support package, while the bottom of the adapter is screwed to the chimney connector.

These adapters are designed so the top end will fit outside the inner wall of the chimney, and the bottom end will fit inside the first section of chimney connector. When assembled in this way, any soot or creosote fall- ing from the inner walls of the chimney will stay inside the chimney connector.

6 30003842