Vermont Castings Pinnacle & Stardance Direct Vent - Rear Vent Gas Heaters

ST241

Cut pad to size and locate as needed

FK105

Fig. 21 Vibration dampening pad location.

Fig. 19 Correct position of fan skirt installation.

4. The rheostat control switch attaches to the left side of

the valve bracket at the front of the stove. (Fig. 20)

MOTOR

Blower Wiring Diagram

Fan Assembly

No. 000-2960 / FK28

•

Remove the plug from the rheostat bracket.

•

Insert the switch box shaft through the hole in the

back of the right side of the valve bracket, aligning

the locator pin with the smaller hole in that bracket.

•

Attach the retaining nut to the switch control shaft

to secure it to the plate.

•

Attach the Control Knob to the rheostat shaft.

•

Use the wire tie to secure the fan and rheostat

wire harnesses together.

Retaining Nut

Rheostat Knob

Rheostat

FK104

Fig. 20 Attach rheostat to bracket.

5.A length of silicone tape is included for installation between the Top Plate and the Rear Shroud, should you find that contact between these two surfaces causes vibration while the fan is operating.

•Remove the Top Plate.

•Cut the self-adhesive tape to size as needed, remove the backing paper and place tape on the top edge of the Shroud at those locations where it will eliminate direct contact between the Shroud and the Top Plate. (Fig. 21)

•Replace the Top Plate.

BLK

 

BLK

BLK

 

 

 

 

 

 

SNAPSTAT

 

 

BLK

WHT

WHT

GRN

ON/OFF

 

RHEOSTAT

WARNING:

 

 

 

DISCONNECT

 

 

 

ELECTRICAL SUPPLY

 

 

 

BEFORE SERVICING

Fig. 22 Blower wiring diagram.

 

Venting System Assembly -

Direct Vent

General Information

The PDV20 and SDVR are approved for installation only with the vent components listed on page 13. Follow the vent component instructions exactly. These instructions apply to both the PDV20 and the SDVR shell.

For U.S. installations: The venting system must conform with local codes and/or the current National Fuel Gas Code, ANSI Z223.1

For Canadian installations: The venting system must conform to the current CSA B149.1 installation code.

Rear Vent

Use Rear Vent Kit 7TFSRSK for an installation where the heater is parallel to the wall and the vent system extends straight back through that wall.

1.Attach Inner Starter Pipe, (found in with the logset), to the stove.

• Run a bead of sealant beneath the pipe bead and

attach to the stove using three 1/4-20 x 3/8” phillips screws provided in the parts bag. (Fig. 23)

16

20003457

Page 15 Page 17
Page 16
Image 16
Vermont Casting 2996, 2950, 2951, 2998, 2997, 2995 manual Venting System Assembly Direct Vent General Information, Rear Vent
Page 15 Page 17

2950, 2995, 2998, 2996, 2997 specifications

Vermont Castings is renowned for its high-quality cast iron stoves and fireplaces, and the models 2996, 2951, 2950, 2998, and 2997 exemplify this legacy. These stoves are designed to provide both efficiency and aesthetic appeal, making them ideal choices for any home.

Starting with the Vermont Casting 2996, this model is a highly efficient wood-burning stove known for its impressive heat output. It features a robust cast iron construction that not only enhances durability but also retains heat effectively, ensuring a long-lasting warmth. The 2996 boasts an advanced air wash system, keeping the glass door clean for a clear view of the flames while promoting optimal burn efficiency.

The Vermont Casting 2951 is another standout model, recognized for its compact size without sacrificing performance. This stove is designed for smaller spaces and is equipped with an innovative catalytic combustor that maximizes fuel efficiency and minimizes emissions. Its elegant design includes a variety of color options, allowing homeowners to select a finish that complements their interiors perfectly.

Moving on to the Vermont Casting 2950, this model offers a blend of tradition and modern technology. It utilizes a secondary combustion system that captures and re-burns gases released during the burning process. This leads to cleaner combustion and increased energy output. The 2950's detailed cast iron craftsmanship not only provides classic appeal but also ensures longevity.

The 2998 model stands out with its large firebox capacity, making it suitable for extended burn times. Designed for wood logs up to 20 inches, it offers an efficient heat output, making it ideal for colder climates. The stove features an easy-to-use air control that allows users to adjust the burn rate for their heating needs, promoting both efficiency and comfort.

Lastly, the Vermont Casting 2997 brings a unique blend of style and functionality. Its distinctive design includes an optional soapstone top, enhancing heat retention and providing an elegant aesthetic. With built-in features like the easy-access ash pan, homeowners can enjoy a hassle-free experience while maintaining their stove.

Overall, these Vermont Castings models showcase advanced heating technologies combined with beautiful design. Their commitment to efficiency, durability, and aesthetics makes them a popular choice for those seeking a reliable heating solution. Whether it's for the cozy ambiance or efficient warmth, Vermont Castings continues to set a standard in the wood stove industry.
Top Page Image Contents