Vermont Castings UVS27
Clearance Requirements
Minimum Clearances to
Combustible Materials
Maintain clearance, (empty space), between combus- tible materials and the heater as specified below for the appropriate firebox shell being installed.
Freestanding Stove
D
B 
A 
C
|
| ST101 |
Hearthmount |
|
|
|
| D |
B | A | C |
|
| ST102 |
A: Mantel/Trim* ......................... 35” (889mm) / 2” (51mm) | ||
B: Side Wall/Trim* ............................................. 2” (51mm) | ||
C: Rear Wall ........................................................ 0” (0mm) | ||
D: Max. Mantel Width .................................... 13” (330mm) | ||
Alcove Clearances
B |
|
|
| B |
|
|
|
|
|
|
|
| D | |
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A
|
|
|
|
|
| ST103 | |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| C |
|
|
|
| |
|
|
|
|
|
| ||
A: Ceiling | 35” (889mm) | ||||||
B: Side Wall | 2” (51mm) | ||||||
C: Rear Wall | 0” (0mm) | ||||||
D: Max. Alcove Depth | 13” (330mm) | ||||||
| A |
|
|
|
| B |
|
|
| C |
|
| S | D |
|
| T | E |
|
|
|
| |
| U |
| F |
| V |
| G |
|
| W | |
|
|
| |
|
| X | H |
|
|
| Y |
|
|
| Z |
|
|
| ST599a |
| Mantel |
| Mantel from |
Ref. | Shelf Depth | Ref. | Stove Top |
A | 13” (330mm) | S | 35” (889mm) |
B | 11¹⁄₄” (286mm) | T | 30” (762mm) |
C | 9³⁄₈” (241mm) | U | 25” (635mm) |
D | 7¹⁄₂” (191mm) | V | 20” (508mm) |
E | 5³⁄₄” (146mm) | W | 15” (381mm) |
F | 4” (102mm) | X | 10” (254mm) |
G | 2¹⁄₄” (57mm) | Y | 5” (127mm) |
H | 1” (25mm) | Z | 2” (51mm) |
Hearth Requirements
The Freestanding Stove and Hearthmount Shell must be installed on rigid flooring. If the appliance is in- stalled on any combustible surface other than wood flooring, such as carpet or tile, a metal or wood panel must be installed to extend the full length and width of the unit.
WARNING
•Do not install this heater in a bathroom or bedroom.
•Installation of this heater must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 / NFPA54.
•This heater creates warm air currents. These currents move heat to wall surfaces next to the heater. Installing the heater next to vinyl or cloth wall coverings or operating the heater where impurities in the air such as tobacco smoke exist, may discolor walls.
•Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater.
20005004 | 5 |
