OPERATING INSTRUCTIONS
COPY OF THE
LIGHTING PLATE INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1. (Australia: AG601, New Zealand: NZS 5261)
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss oflife.Improperinstallation,adjustment,alteration,serviceormaintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or gas supplier.
Gas Control Valve:
As the gas control valve turns ON and OFF, a dull clicking sound may be audible, this is normal operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will expand and contract at different rates resulting in some "cracking" and "ticking" sounds will be heard throughout the cycling process.
MAINTENANCE
INSTRUCTIONS
A)This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.
B)BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
-Do not try to light any appliance
-Do not touch any electric switch, do not use any phone in your building
-Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.
-If you cannot reach your gas supplier, call the fire department.
C)Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D)Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.
This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.
1) Always turn off the gas valve before clean- |
ing. For |
tions. Keep the burner and control compart- |
ment clean by brushing and vacuuming at |
least once a year. |
When cleaning the logs, use a clean soft |
paint brush as the logs are fragile and easily |
damaged. |
2) Clean glass (never when unit is hot), appli- |
ance, door and louvers with a damp cloth. |
Never use an abrasive cleaner. |
The heater is finished in a heat resistant |
paint and should only be refinished with |
heat resistant paint (not with wall paint). |
Waterford uses Stove Brite Paint - Metallic |
Black #6309. |
CAUTION:Hotwhileinoperation.Donottouch.SevereBurnsmayresult.Due to high surface temperatures keep children, clothing and furniture, gasoline and other liquids having fammable vapors away. Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.
LIGHTING INSTRUCTIONS
STOP! Read | the | safety information 4) Push in control knob all the way and | |
above on this label. | hold in. Continually push and release | ||
1) Push in gas control knob slightly and | the black button on spark igniter until | ||
turn clockwise | to “OFF”. Knob | pilot lights. Continue to hold the | |
cannotbeturnedfrom“PILOT”to“OFF” | control knob in for about 1/2 minute | ||
unless knob is pushed in slightly. Do | after the pilot is lit. Release knob and | ||
not force. |
|
| it will pop back up. Pilot should remain |
2) Wait five (5) minutes to clear out any | lit. If it goes out, repeat steps 1) to 4). | ||
gas. If you then smell gas STOP! follow | If knob does not pop up when released, | ||
“B” in the safety information above on | stop and immediately call your service | ||
this label. If you don’t smell gas, go to | technician or gas supplier. If the pilot will | ||
the next step. |
| not stay lit after several tries, turn the gas | |
3) Turn knob | on gas control counter- | control knob to “OFF” and call your | |
clockwise |
| to“PILOT”. | service technician or gas supplier. |
PILOT BURNER |
| OFF 5) Turn gas control knob | |
VEILLEUSE |
|
| |
THERMOPILE |
|
| to “ON”. |
ELEMENT |
|
| 6) Use rocker switch to op- |
|
| erate main burner. | |
THERMO- |
|
| |
|
|
| |
ELECTRIQUE |
|
|
|
TO TURN OFF GAS APPLIANCE
1)Push in the gas control knob slightly and 2) Turn off all electric power to the turn clockwise
to “OFF”. Do not force. appliance if service is to be performed.
You may shut off the pilot during prolonged non use periods to conserve fuel.
DO NOT REMOVE THIS INSTRUCTION PLATE 908-017b
3) | Make a periodic check of burner for proper |
| position and condition. Visually check the |
| flame of the burner periodically, making |
| sure the flames are steady; not lifting or |
| floating. If there is a problem, call a qualified |
| service person. |
4) | The appliance and venting system must be |
| inspected before use, and at least annually, |
| by a qualified field service person, to en- |
| sure that the flow of combustion and ven- |
| tilation air is not obstructed. |
| During the annual service call, the burner |
| should be removed from the burner tray and |
| cleaned. Replace the embers but do not |
| block the pilot. |
5) | Verify proper operation after servicing. |
6) | Keep the area near the appliance clear and |
| free from combustible materials, gasoline |
| and other flammable vapours and liquids. |
CAUTION: ANY SAFETY SCREEN ORGUARDREMOVEDFORSERV- ICING AN APPLIANCE MUST BE REPLACED PRIOR TO OPERAT- ING THE APPLIANCE.
16 | Waterford E61 Gas Fireplace Insert |
