Wayne 353601-001 specifications PS/BC Installation, Methods 1, Control Box Installation

Operating Instructions and Parts Manual
Pump Installation
(Continued)
3. A check valve will be required in		Floor
	the discharge line of BOTH the
		Joist		“Y”
	Main AC pump and the ESP45					Rigid PVC
			Connector
	pump to prevent recirculation of					Pipe
	water into the sump pit. System will		45°
	not function without two check
	valves.		Elbow			Check Valve
		PS/BC
4. Cut a 4’ section of 11/4" or 11/2"						(See Step 10)
	diameter rigid PVC pipe. Cement
	11/2" pipe to a threaded fitting.
	Cement 11/4" pipe into pipe
	coupling. Attach 11/4" pipe section	Batteries
	to the ESP45 discharge adapter.
5. Screw on to pump discharge.
	Be careful not to
	strip or cross thread
plastic fittings or check valves. Flex hose
is not recommended. Rigid PVC or metal
pipe is required for a permanent
installation.		Battery
6. Place the pump with the 4’ section			ESP45
		Box				Existing Pump
	of PVC pipe on the sump floor or		Pump
	on an elevated surface if required.	Figure 3 - Method 2
7. Attach a rubber check valve (sold
	separately) to the top of the	Methods 1 and 2				Always disconnect
	discharge pipe. This will allow the
		Install float switch at least 10”-12”				AC power and
	pump or check valve to be removed
				remove pump fuse before connecting or
	easily for servicing.	above bottom of sump pit so that
				disconnecting battery.
8.	Duplicate the discharge piping	backup unit turns on only when the		1. Select a suitable position on the floor
	arrangement for the primary AC	water level is higher than the normal
					near the sump pit to place the battery
	pump if the existing discharge line	“on” level for main pump. Use the hose
					case. Be certain that the PS/BC power
	has to be adjusted to accommodate	clamps provided to secure the switch to
					cord will reach AC power, and that
	a second pump.	the discharge pipe. Make sure power
					the sump pump power cord will reach
9.	Glue a 45º elbow to the short pipe	wires and hose clamp ends do not
					the PS/BC. Make sure the battery case
	on the ESP45 pump. Glue a “Y”	interfere with float switch, pump inlet,
					vent holes are unobstructed.
	adapter to the short pipe on the	or main pump operation. Backup pump
				ELEVATE PS/BC BY MOUNTING ON
	existing pump, as shown in	must not be allowed to run dry.
	illustration for Method 2.	PS/BC Installation		WALL OR SETTING ON A SHELF. SLOTS
				IN THE BACK SIDE OF PS/BC ARE
10. Glue a short piece of PVC pipe		Use Power Supply/
				AVAILABLE FOR WALL MOUNTING.
	between the 45º elbow and the “Y”.
		Battery Charger
				Control Box Installation
NOTE: Check valves can be placed		(PS/BC) indoors, in a well-ventilated
directly in the pump discharge if		area. Do not expose PS/BC to rain or				If cables are
		snow. Do not use an extension cord. Do				reversed, damage
desired. However, for ease of
		not disassemble PS/BC. Be sure PS/BC		to the PS/BC or battery could result,
disassembly, it is recommended that
		ventilation holes are unobstructed. If		and warranty will be void.
check valves be placed above the sump		PS/BC is dropped or damaged, do not		Dangerous hydrogen gas can be
as shown in Figure 3.		operate; return to manufacturer for
				released from batteries while charging.
The remainder of the discharge pipe		service.
				Sparks can ignite the gas in an
		Risk of electrical
installation will vary depending on				enclosed space. Wear safety goggles
individual circumstances. Using sound		shock! Use a GFCI		when connecting batteries. Battery
		(Ground Fault Circuit Interrupter)
plumbing practices, route the				connections should be made in a well-
		receptacle to reduce the risk of fatal
discharge pipe to an exterior wall by				ventilated area.
		electrical shock. Grounded receptacle must
the shortest distance.		be rated for at least 5 amps.
www.waynepumps.com

4