Wayne-Dalton 346919 installation instructions Pull Handles, Bottom Corner Brackets

hole onto the center stile. Drill 1/16” pilot holes at the marked hole locations. Fasten both lift handles to the center stile using #10 X 5/8” pan head self tapping screws.

If the door came with two sets of lift handles repeat the same process for the other lift handles.

Center stile		Center stile
			Vertical
				line
	3-7/8”	Vertical	3-7/8”
		line
	Horizontal		Horizontal
Center line	line	Center line	line
Lock section		Lock section
			(4) #10 X 5/8” Pan
	(2) #10 X 5/8” Pan		head self tapping
	head self tapping		screws
		screws
	Lift		Lift
	handle		handle	Center
Center stile		Lift		stile
		handle

Typical placement of lift
handles referenced on
single wide doors			Lock
	Lift handles		section
	Pull handle
	Bottom section		20” Minimum to
			30” Maximum
Typical placement of lift handles referenced on double wide doors
Lift handles
	Bottom		Lock
	section		section
	Pull handle	20” Minimum to 30” Maximum	Pull handle
6	Pull Handles
	Tools: Tape Measure, Pencil, Power Drill, 1/16” Drill Bit

Locate and mark the horizontal and vertical center on the bottom rail of the bottom section, on single car doors.

Center the pull handle using the vertical and horizontal lines as referenced on the bottom section rail. Using the pull handle as a template, mark the two hole locations in the pull handle onto the horizontal line of the bottom section rail. Drill 1/16” pilot holes at the marked hole locations. Fasten pull handle(s) using (2) #10 X 5/8” pan head self tapping screws.

If your door came with two pull handles, locate them directly below the lift handles and repeat the installation process.

Center stile
Bottom section		(2) #10 X 5/8” Pan
		head self tapping
	Pull handle
Bottom rail		screws

Typical placement of pull
handle referenced on
single wide doors		Lock
Lift handles		section
Pull handle
Bottom section		20” Minimum to
		30” Maximum
Typical placement of pull handles referenced on double wide
Lift handles
Bottom		Lock
section		section
Pull handle	20” Minimum to 30” Maximum	Pull handle

7	Bottom Corner Brackets
	Tools: Power drill, 7/16” Socket driver

NOTE: The bottom section can be identified by the smallest graduated edge hinge of the factory installed graduated edge hinges, see Parts Breakdown on page 2

Locate the left hand bottom corner bracket. Align the bottom corner bracket horizontally with the top edge of the factory attached bottom corner bracket. Also align the bottom corner bracket vertically with the left edge of the bottom section. Attach the bottom corner bracket using (4) 1/4”- 20 x 11/16” self drilling screws and (1) 1/4” - 20 x 5/8” tamper proof screw, as shown.

WARNING

Failure to ensure tight fit of cable loop over milford pin could result in counterbalance lift cable coming off the pin, al- lowing the door to fall, possibly resulting in severe or fatal injury.

Uncoil the counterbalance cables. Place clevis pin into the inside tab of the bottom corner bracket and slide the cable loop of the counterbalance lift cable onto pin. Continue sliding clevis pin thru the outside tab of the bracket. Place a washer onto mildford pin and secure in place using a cotter pin, as shown.

Insert a short stem track roller into the factory attached bottom corner brackets and another into the #1 graduated end hinges at the top of the bottom section. Repeat for other side.

Note: Larger doors will use long stem track rollers with double graduated end hinges.

NOTE: Verify bottom weather seal is aligned with bottom section. If there is more than 1/2” excess weather seal on either side, trim weather seal even with bottom section.

	Right hand bottom					(4) 1/4” - 20 x 11/16”
	corner bracket					Self drilling screws
			Counterbalance
			lift cable
			Cotter pin		Clevis
					pin
						Bottom
			Washer			weather
						seal
		Short stem				(1) 1/4” - 20 x 5/8”
Left hand bottom		track roller				Tamper proof screw
corner bracket					Left hand bottom corner bracket
	Counterbalance			NOTE: The
	cable					Bottom section
			bottom bracket
						astragal
			is not shown in
Inside	Washer
			illustration, for
tab
			clarity purposes.
	Cotter
	pin		Clevis
			pin
			Roller			Factory attached
Outside tab						bottom bracket

7

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,

refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com